Ramsey Winch REP 8000

Questions and Answers

J
Jay BrooksAug 1, 2025
What to do if my Ramsey Winches motor will not operate?
- M
  michaelmyersAug 1, 2025
  If your Ramsey Winches motor won't operate, here's what to check: * **Solenoid Issues:** Jar the solenoid to free the contacts. Test by applying the correct voltage (12 or 24 volts) to the coil terminal; it should click. Disengage the winch clutch, disconnect the remote control switch, and jump the pins at the 8 and 4 o’clock positions, and then the 8 and 10 o’clock positions. The motor should run. * **Remote Control Switch:** Follow the same steps as for solenoid issues to test the remote control switch. * **Motor Problems:** If the solenoids are working, check for voltage at the armature post and replace the motor if needed. * **Loose Connections:** Tighten any loose connections found on the bottom side of the hood and on the motor.
T
theresa80Aug 5, 2025
Why does my Ramsey Winches motor run, but with insufficient power or low line speed?
- S
  Susan RichardsAug 5, 2025
  If your Ramsey Winches motor runs but lacks power or has a low line speed, the following could be the causes: * **Insufficient Battery:** Check the battery terminal voltage under load. If it's 10 volts or less, replace the battery or add another one in parallel. * **Bad Connection:** Inspect battery cables for corrosion. Clean and grease them if necessary. * **Insufficient Charging System:** Consider replacing your current system with one that has a larger capacity.
J
Jacqueline RogersAug 9, 2025
What to do if my Ramsey Winches motor runs in only one direction?
- L
  Lisa PenningtonAug 9, 2025
  If your Ramsey Winches motor only runs in one direction, the issue might be: * **Defective or Stuck Solenoid:** Try jarring the solenoid to release the contacts. Test it by applying the appropriate voltage (12 or 24 volts) to the coil terminal; you should hear a click. Disengage the winch clutch, unplug the remote control switch, and jump the pins at the 8 and 4 o’clock positions, and then the 8 and 10 o’clock positions. The motor should run. * **Defective Remote Control Switch:** Follow the same steps as for a defective solenoid to test the remote control switch.
B
bmirandaAug 14, 2025
Why is my Ramsey Winches motor running extremely hot?
- G
  garciaericaAug 14, 2025
  If your Ramsey Winches motor is running extremely hot, it may be due to a long period of operation. Cooling-off periods are essential to prevent overheating.
D
Daniel ThompsonAug 18, 2025
What to do if the cable drum on my Ramsey Winches will not freespool or is difficult to freespool?
- A
  Angel RichardsonAug 18, 2025
  If the cable drum on your Ramsey Winches won't freespool or is difficult to freespool, consider these potential causes: * **Clutch not disengaged:** Check the clutch operation according to the nameplate. Ensure the clutch shifter knob is fully in the “OUT” position. * **Winch Mounting:** Check the mounting to see that installation instructions have been followed. * **Capscrews:** Remove the gear housing cover and all gears from inside the gear housing. Disengage the clutch and check to see that the ring gear will rotate by hand. If it will not, using a hex (allen) wrench, slightly loosen all the capscrews and then snugly re-tighten them in criss-cross pattern, but do not over-tighten. The ring gear must rotate by hand. Re-assemble the winch.
J
Jacob BrownAug 22, 2025
What should I do if my Ramsey Winches motor is water damaged?
- C
  Christopher WilliamsAug 22, 2025
  If your Ramsey Winches motor is water damaged (e.g., submerged or exposed to high-pressure car wash), allow it to drain and dry thoroughly. Then, run the motor without a load in short bursts to dry the windings.
K
Karen WebsterAug 27, 2025
What to do if my Ramsey Winches motor runs, but the drum does not turn?
- J
  joseph25Aug 27, 2025
  If your Ramsey Winches motor runs, but the drum doesn't turn, it could be that the clutch is not engaged. If the clutch is engaged but the symptom persists, it will be necessary to disassemble the winch to determine the cause and repair it.