Ransburg 75785 - User Manual

Questions and Answers

C
carriejonesSep 23, 2025
Why is my Ransburg 75785 leaking fluid slightly at the nozzle when the trigger is released?
- A
  Anthony CoxSep 23, 2025
  A slight fluid leak at the nozzle of your Ransburg Paint Sprayer when the trigger is released can occur if the nozzle isn't secure, so try tightening it. It could also mean the air valve is closing before the fluid valve; in this case, adjust the needle shaft/electrode travel.
J
Joseph CopelandAug 25, 2025
Why is there no high voltage in my Ransburg Paint Sprayer?
- U
  ubaileyAug 25, 2025
  If you're experiencing improper or no high voltage with your Ransburg Paint Sprayer, the possible causes include: * Faulty low voltage cable connections: Check and secure the connections at both the applicator and the control unit. * Faulty transformer/hook assembly: Replace it. * Improper or no ground at the control unit: Correct the grounding (1 megohm maximum ground to target resistance). * Faulty barrel/cascade assembly: Replace it. * Faulty low voltage cable: Replace it.
K
Katie Lawson MDAug 25, 2025
What causes air issues in a Ransburg 75785 Paint Sprayer?
- R
  Roger MooreAug 26, 2025
  Air issues in your Ransburg Paint Sprayer can stem from: * Clogged air passages in the applicator or air line: Blow them out. * Inadequate air source: Increase the air supply. * Paint in the air passage: Clean and blow it out.
D
Daniel RobersonAug 27, 2025
What to do if my Ransburg 75785 pattern will not shape?
- S
  Sabrina JonesAug 27, 2025
  If the spray pattern on your Ransburg Paint Sprayer isn't shaping correctly, it could be due to: * A clogged or faulty fan air valve: Clean, repair, or replace it. * Clogged air passages in the applicator or air line: Blow them out, clean, or replace them. * A worn, faulty, or clogged air cap: Clean or replace it.
S
Sarah JohnsonAug 27, 2025
What causes a Ransburg 75785 Paint Sprayer to have heavy spitting or a deformed pattern?
- J
  John GarciaAug 27, 2025
  Extremely heavy spitting or a severely deformed pattern in your Ransburg Paint Sprayer can be caused by: * Using the wrong air cap/fluid nozzle combination: Ensure you are using the correct combination. * A faulty air cap: Replace it.
S
Sara JacobsonSep 14, 2025
Why is my Ransburg Paint Sprayer not providing air?
- C
  Crystal ComptonSep 14, 2025
  If your Ransburg Paint Sprayer isn't providing air, first check for clogged air passages in the gun or air line and blow them out. It could also be due to an inadequate air source, so increase it. Another potential cause is paint in the air passage, so clean and blow it out.
M
Michael ClarkSep 12, 2025
Why isn't my Ransburg 75785 shaping the pattern correctly?
- K
  Kimberly BushSep 12, 2025
  If your Ransburg Paint Sprayer's pattern isn't shaping correctly, it could be due to a few reasons. First, check for a clogged or faulty fan air valve; clean, repair, or replace it as needed. Second, air passages in the gun or air line might be clogged; blow them out, clean, or replace them. Lastly, the air cap could be worn, faulty, or clogged; clean or replace it.
D
Dominique SawyerSep 13, 2025
What causes 'Wrap Back' with a Ransburg 75785 Paint Sprayer?
- W
  Wesley TerrySep 13, 2025
  Wrap back with your Ransburg Paint Sprayer can occur due to several reasons. Check for an improper target ground and correct it, ensuring a maximum ground to target resistance of 1 megohm. Improper spray technique may be the cause. Also, inspect the booth exhaust and correct if necessary. Excessive atomizing air pressure can also lead to wrap back, so reduce the pressure. Finally, excessive distance between the gun and target can cause this issue, so decrease the distance.
K
Kaitlyn ClarkSep 4, 2025
Why is there air coming from plugged machine holes in the body of my Ransburg 75785?
- G
  gkingSep 5, 2025
  If you notice air escaping from plugged machine holes in the body or at the air valve cap at the rear of your Ransburg Paint Sprayer, it's likely due to loose or defective plugs or cap. Tighten them or replace the Teflon tape.
B
Bryan ThompsonSep 2, 2025
What to do if my Ransburg 75785 leaks fluid at the nozzle when the trigger is released?
- A
  adamdavisSep 2, 2025
  If your Ransburg Paint Sprayer has a slight fluid leak at the nozzle when the trigger is released: * Ensure the nozzle is secure and tighten it if necessary. * Adjust the needle shaft/electrode travel if the air valve is closing before the fluid valve.