Raptor E820 - Tail Unit; 尾部總成組裝

No.
1
2
3
4
5
6
7
8
9
10
11
QtyDescription 名稱
TAIL DRIVE SHAFT
TAIL DRIVE SHAFT BRG
LOCK NUT, M2.5
TAIL DRIVE SHAFT LINKER
SOCKET SCREW, M2.5x12
CARBOM TAIL BOOM
TORX SCREW, M3x8
TAIL STOPPER
SOCKET SCREW, M3x10
CARBON VERTICAL FIN
METAL TAIL BOOM SUPPORT BRACKET
尾驅動軸
尾驅動軸軸套組
止鬆螺帽, M2.5
尾驅動連接棒
內六角螺絲, M2.5x12
碳纖尾管
星型螺絲
, M3x8
尾管止擋塊
內六角螺絲, M3x10
碳纖垂直安定面
金屬尾管支撐固定座
1
2
2
2
2
1
2
1
1
1
1
LOCK NUT, M2.5
止鬆螺帽, M2.5
No.
12
13
14
15
16
17
18
19
20
21
22
QtyDescription 名稱
SOCKET SCREW, M3x8
SOCKET SCREW, M3x6
METAL TAIL SERVO MOUNT
SELF TAPPING SCREW, M2x8
ROD GUIDE
TAIL BOOM SUPPORT END
SOCKET SCREW, M3x12
NUT, M2
SOCKET SCREW, M2x10
CARBON TAIL BOOM SUPPORT
FRAME SPACER
內六角螺絲, M3x8
內六角螺絲, M3x6
金屬伺服機固定座
自攻螺絲(粗), M2x8
推拉桿固定環
尾管支撐架接頭
內六角螺絲, M3x12
六角螺帽, M2
內六角螺絲, M2x10
碳纖尾管支撐架
側板支柱
1
2
2
3
3
4
4
4
4
2
1
Apply C.A Glue
使用快乾膠黏合
-17-
Tail Unit / 尾部總成組裝
Apply threadlocker
使用螺絲防鬆膠
SOCKET SCREW, M2x10
內六角螺絲, M2x10
SOCKET SCREW, M3x10
內六角螺絲, M3x10
SOCKET SCREW, M2.5x12
內六角螺絲, M2.5x12
SELF TAPPING SCREW, M2x8
自攻螺絲(粗), M2x8
SOCKET SCREW, M3x8
內六角螺絲, M3x8
NUT, M2
六角螺帽, M2
Bag I+J
Assemble left and right
side the same way
左右側組件相同
(21)
(18)
(17)
(17)
(18)
(18)
(20)
(19)
(19)
(20)
(15)
(13)
(16)
(12)
(16)
(16)
(11)
(14)
(22)
Add a drop of thin CA glue on the Tail Drive Shaft next to where
the bearing should be, and then slide the bearings over the
position quickly; the distance from the Shaft Drive End to the
Rubber Shaft Bearing Support is approx. 278mm / 10.94”.
在尾傳動軸上軸承固定位置前方，塗抹少量快乾膠，迅速滑動軸承至定
位固定；該定位大約距離軸傳動接頭278mm / 10.94”處。
278mm/10.94”
278mm/10.94”
(4)
(3)
(5)
(4)
(2)
(2)
(5)
C.A
(1)
(6)
(3)
(7)
(10)
(8)
(9)
SOCKET SCREW, M3x12
內六角螺絲, M3x12
TORX SCREW, M3x8
星型螺絲
SOCKET SCREW, M3x6
內六角螺絲, M3x6
Secure the screws into the Frame
Spacer when attaching the Tail Boom
Support End on the Main Frames.
安裝尾管支撐架於側板上時，請注意需將
鎖固螺絲鎖固於六角固定支柱上。
Rear View 後視圖
(22)
(18)(18)