Rath 2100 Series Operation Manual

Rath 2100 Series

6 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

N56W24720 N. Corporate Circle Sussex, WI 53089

800-451-1460 www.rathcommunications.com

RP8500WIFISIP

Ver. 3

07/18

Made in the USA

3 Year Warranty

Installation & Operations Manual

2100 Series Wi-Fi

VoIP Phone

Table of Contents

Other manuals for Rath 2100 Series

Installation & Operation Manual7 pages

Questions and Answers:

A
anthonysanchezAug 21, 2025
What to do if my Rath 2100 is dead and won't call or program?
- A
  Albert BurkeAug 22, 2025
  If your Rath IP Phone is completely unresponsive, try the following: * Make sure the phone is connected and receiving POE from the Network Switch. * Confirm the voltage switch on the POE adapter is set to 12v. * Check the LEDs on all components, including the POE adapter, IP board, and yellow circuit board. * Verify that the phone does not exceed the 320’ distance limitation from the Network Switch. * It's possible the POE Switch can't handle the power requirements; POE+ or POE++ is recommended. * You can also try resetting the phone.
W
wheelermichaelAug 23, 2025
What to do if Rath IP Phone dials out but goes busy?
- R
  Rebecca RoseAug 23, 2025
  If your Rath IP Phone dials out but immediately goes to a busy signal, consider these possibilities: * Log into the VoIP Phone and verify that it still shows registered under Line 1. * Verify the dialing string is programmed into the Phone, especially if an 8 or 9 is needed to dial out. * The Phone may need to dial an extension rather than a standard 11 digit number.
L
Lisa SmithAug 26, 2025
Why won't my Rath 2100 IP Phone call out and just sits with a dial tone?
- C
  christine04Aug 26, 2025
  If your Rath IP Phone only provides a dial tone but won't complete the call, try these solutions: * Follow the steps in Phone Programming to verify the dial out number programmed into the phone. * Verify the phone is in Standard Mode by pressing ENTER, 1, 9, ENTER, 1, then press and hold STOP for 3 seconds. * Ensure the number being programmed into the phone is a valid, routable number.
D
David CamachoAug 27, 2025
What to do if my Rath 2100 doesn’t respond when the call button is pushed?
- B
  brendan34Aug 28, 2025
  If your Rath IP Phone doesn't respond when the call button is pushed, and there's no LED or audio, check the following: * Verify that the line cord from the RJ11 jack on the yellow circuit board is connected to the RJ11 jack on the VoIP board. * Check that the voltage switch on the POE adapter is set to 12v. * The push button may be non-functional. Remove the black switch JST connector from the yellow circuit board and short across the 2 pins on the board in the connector using a flat metal screwdriver. * Verify that the phone is still connected and getting POE from the Network Switch. * Verify that the phone still shows as Registered. * You can also try to reset the phone.
J
juan24Aug 30, 2025
How to fix distorted or low audio on Rath 2100 IP Phone?
- M
  mariah01Aug 30, 2025
  If the audio on your Rath IP Phone is distorted or very low, here are some troubleshooting steps: * Adjust VR1 and VR2 potentiometers on the yellow circuit board. * Make sure nothing is blocking the speaker or microphone holes on the face plate. * Verify network traffic isn’t slow.
G
gbaileyAug 19, 2025
Why is my Rath IP Phone not showing as registered?

Rath 2100 Series Specifications

General

Brand	Rath
Model	2100 Series
Category	IP Phone
Language	English

Related product manuals

Rath 2100-956SR

Preview: Rath 2100-LTEGSM4

Rath 2100-LTEGSM4

Rath 2100-958SSRC2

Rath SmartView 2100-SVCF

Rath SmartView 2100-SVFCOMP

Rath 2500-210PSS

Rath 2400-805SP

Rath 2500-28RCF

Rath 2500-205PSS

Rath 2400-808NSP

Rath 2300-614GSM4