Rath SmartPhone VI User Manual

Page 5
Programming for Ring Down Phone Lines using
Onboard Keypad:
In Ring Down Mode, the phone will not dial any
programmed numbers. The phone will go off-hook
and the phone line itself will connect to a monitoring
location. Programming phone to Ring Down Mode
will automatically set the Talk Time to 3 minutes.
1. Press ENTER on the keypad to begin programming
2. Press 1, 9, ENTER, 2
3. Press and hold STOP for 3 seconds to exit
programming
Note: If the phone is inadvertently put into Ring Down
Mode, press 1, 9, ENTER, 1 while in programming to
put the phone back into Standard Mode.
Programming Location Message using Onboard
Keypad:
SmartPhones can play a location message when the
call is answered. This feature is used when the phone
is calling a phone number that cannot identify where
the call is coming from by caller ID or needs more
location information than caller ID can provide. This
feature is turned on by default. Perform the steps
below to program the location message feature.
1. Press ENTER to begin programming
2. Press 1, 3, ENTER, (1, 2, or 3) (1 will play
message once, 2 will play twice, 3 will play
message on a loop until operator presses *)
3. Press 6, RECORD, wait for the “beep”, speak
location message, STOP
4. Press 6, PLAY/PAUSE to play message back
5. Press and hold STOP for 3 seconds to exit
programming
To turn location message off, press ENTER, 1, 3,
ENTER, 0, press and hold STOP for 3 seconds.
Note: Party can replay message by pressing *, *.
Programming for Ring Down Phone Lines using
Remote Programming:
1. Call the phone number that the SmartPhone is
installed on
2. After the rst simulated ring, press #, # and wait for a
conrmation tone
3. Key in the security code (default is 1, 1, 1, 1) and
wait for a conrmation tone
4. Press 1, 9, *, 2 and wait for a conrmation tone
5. Press *, #, 0 to exit programming and wait for a
conrmation tone
6. Press *, # to hang up the phone
Note: If the phone is inadvertently put into Ring Down Mode,
press 1, 9, *, 1 while in programming to put the phone back
into Standard Mode.
Programming Location Message using Remote
Programming:
1. Call the phone number that the SmartPhone is
installed on
2. After the rst simulated ring, press #, # and wait for a
conrmation tone
3. Key in the security code (default is 1, 1, 1, 1) and
wait for a conrmation tone
4. Press 1, 3, *, (1, 2, or 3) and wait for a
conrmation tone (1 will play message once, 2
will play message twice, 3 will play message on a
loop until operator presses *)
5. Press 6 , *, wait for the “beep”, speak location
message, #
6. Press 6, # to play message back
7. Press *, #, 0 to exit programming and wait for a
conrmation tone
8. Press *, # to hang up the phone
To turn off location message, press 1, 3, *, 0 while in
programming.
Note: Party can replay the message by pressing *, *.
Programming Phone Line Check:
SmartPhones have a built-in phone line check. When the phone detects either a loss of dial tone or operating voltage,
the line relay labeled “ALARM” on the phone will go from open to closed. This feature is turned on by default and set
to check the phone line every 10 minutes.
Note: If the phone is installed on a Ring Down style phone line, it may cause “ghost dials” due to the phone going off
hook to check the line. Please use one of the following options to modify this feature.

Rath SmartPhone VI Specifications

General

Brand	Rath
Model	SmartPhone VI
Category	Conference System
Language	English