Rath SmartPhone VI User Manual

Page 4
Quick Set-Up from Onboard Keypad:
1. Program Number
a. Press ENTER
b. Press 1, ENTER, the number you want the
phone to dial, STOP
2. Program Message
a. Press 1, 3, Enter, 2 for message to play
twice
b. Press 6, RECORD, after the “beep” speak
message, press STOP when nished
3. Press 6, PLAY/PAUSE, message will
playback
4. Press and hold STOP for 3 seconds to exit
programming
Quick Set-Up using Remote Programming:
1. Program Number
a. Call the phone number that the SmartPhone is installed on
b. After the rst simulated ring, press #, # and wait for a
conrmation tone
c. Key in the security code (default is 1, 1, 1, 1) and wait for
a conrmation tone
d. Press 1, *, (phone number), *, # and wait for a
conrmation tone
2. Program Message
a. Press 1, 3, *, 2 for message to play twice and wait for a
conrmation tone
b. Press 6, *, after the “beep” speak location message, press
# and wait for a conrmation tone
3. Press 6, # to play message back
4. Press *, # , 0 to exit programming and wait for a conrmation
tone
5. Press *, # to hang up the phone
Programming Primary Phone Number
using Onboard Keypad:
1. Press ENTER on the keypad to begin
programming
2. Press 1, ENTER, the number you want the
phone to dial, STOP
3. Press and hold STOP for 3 seconds to
exit programming
Note: In situations where a delay is needed,
such as needing an 8 or 9 to dial out, use the
PLAY/PAUSE button on the keypad. The button
can be pressed multiple times for a longer delay.
One PAUSE = 1 second.
Programming Secondary Phone
Numbers using Onboard Keypad:
1. Press ENTER on the keypad to begin
programming
2. Press 2, ENTER, the number you want the
phone to dial, STOP
Note: SmartPhones can call up to 5 numbers.
Repeat the steps above for subsequent
numbers. Substitute 2 with 3, 4, or 5 depending
on the order you want the numbers to be dialed.
Example: For the third number to be dialed,
it would be 3, ENTER, phone number, STOP.
3. Press and hold STOP for 3 seconds to exit
programming
Detailed Programming
Programming Primary Phone Number using Remote
Programming:
1. Call the phone number that the SmartPhone is installed on
2. After the rst simulated ring, press #, # and wait for a
conrmation tone
3. Key in the security code (default is 1, 1, 1, 1) and wait for a
conrmation tone
4. Press 1, *, (phone number),* , # and wait for a conrmation
tone
5. Press *, #, 0 to exit programming and wait for conrmation tone
6. Press *, # to hang up the phone
Note: In situations where a delay is needed, such as needing an
8 or 9 to dial out, use #, * for a pause. #, * can be pressed
multiple times for a longer delay. One PAUSE = 1 second.
Programming Secondary Phone Numbers using Remote
Programming:
1. Call the phone number that the SmartPhone is installed on
2. After the rst simulated ring, press #, # and wait for a
conrmation tone
3. Key in the security code (default is 1, 1, 1, 1) and wait for a
conrmation tone
4. Press 2, *, (phone number), *, # and wait for a conrmation tone
Note: SmartPhones can call up to 5 numbers. Repeat the steps
above for subsequent numbers. Substitute 2 with 3, 4, or 5
depending on the order you want the numbers to be dialed.
Example: For the third number to be dialed, it would be 3, *,
phone number, *, #.
5. Press *, #, 0 to exit programming and wait for a conrmation tone
6. Press *, # to hang up the phone

Rath SmartPhone VI Specifications

General

Brand	Rath
Model	SmartPhone VI
Category	Conference System
Language	English