Raymarine T300 - User Manual

Other manuals for Raymarine T300

Questions and Answers

V
Victoria FranklinAug 12, 2025
What to do if Raymarine Thermal camera video is not displayed?
- A
  amydennisAug 12, 2025
  If your Raymarine thermal camera isn't displaying video, there might be a few reasons: * The camera could be in Standby mode. To fix this, use the camera controls (either the thermal camera application or JCU) to wake the camera from standby. * There might be a problem with the video connections. Check that the video cables are properly connected, ensure the video is connected to video input 1 at the multifunction display or GVM, and verify the correct video input is selected on the display. * There could be a power supply issue. Check the power connections to the camera and JCU / PoE injector (if used), ensure the power switch/breaker is on, and check the fuse/breaker state.
J
Joseph AveryAug 16, 2025
Why is my Raymarine Thermal camera image too dark or too light?
- S
  Sarah KhanAug 16, 2025
  If your Raymarine thermal camera image appears too dark or too light, consider the following: 1. The display brightness might be set too low. Adjust the brightness using the controls on the display. 2. The contrast or brightness settings in the thermal camera application could be improperly set. Use the softkeys in the application to adjust these settings. 3. The Scene Mode might not be suitable for the current conditions. Try using the SCENE button to select a more appropriate mode.
K
Karen RossAug 19, 2025
What causes a noisy image on Raymarine T300 Thermal cameras?
- B
  Bill WashingtonAug 20, 2025
  A noisy image on your Raymarine thermal camera can be caused by: * A poor quality or faulty video cable. Ensure the video cable is as short as possible, use a high-quality shielded cable suitable for marine environments. * Electromagnetic interference (EMI) from another device. Use a high-quality shielded cable and ensure proper cable separation between data and power cables.
T
Tara CooperAug 25, 2025
What to do if Raymarine display or keyboard cannot control thermal camera?
- K
  Kristin SmithAug 25, 2025
  If you cannot control the thermal camera from the Raymarine display or keyboard, the thermal camera application may not be running. Ensure the thermal camera application is running on the multifunction display, rather than the video application.
W
wesley46Aug 28, 2025
Why can't I switch between thermal and visible (VIS / IR) video image on Raymarine?
- S
  Steven HillAug 28, 2025
  If you cannot switch between thermal and visible (VIS / IR) video images on your Raymarine thermal camera, it could be due to the following reasons: * The camera may not be a dual payload model. Only dual payload (dual lens) thermal cameras support VIS / IR switching. * The VIS / IR cable may not be connected. Ensure that the VIS / IR cable is connected from the camera to the Raymarine system. Note that the IR-only cable does not support switching.
L
Luis SchultzAug 31, 2025
What causes erratic or unresponsive controls on Raymarine T300?
- A
  ashley77Aug 31, 2025
  Erratic or unresponsive controls on your Raymarine thermal camera can be caused by: * A SeaTalkhs problem. Check that the controller and thermal camera are correctly connected to the SeaTalkhs network, either directly or via a SeaTalkhs switch. * A control conflict, such as multiple users at different stations using controllers simultaneously. Ensure that no other controllers are in use at the same time. * A problem with the controller. Check the power/SeaTalkhs cabling to the controller and PoE injector (PoE only used with optional Joystick Control Unit).
S
Susan MasonSep 4, 2025
Why does my Raymarine Thermal camera image freeze momentarily?
- M
  mooreamberSep 4, 2025
  The image on your Raymarine thermal camera may pause momentarily due to the Flat Field Correction (FFC) cycle. Just before the FFC, a small green square will appear in the upper left corner of the screen.
S
Shelia CookSep 7, 2025
How to correct an inverted image on a Raymarine Thermal camera?
- J
  Jacqueline WhiteSep 8, 2025
  If the image on your Raymarine thermal camera is inverted (upside down), the camera’s “Ball down” setting is likely incorrect. Ensure that the Ball down setting within the thermal camera system setup menu is set correctly.