TO
ENTER A NEW TIMED OUTPUT VALUE *
FIRST: Press and hold the 71"
(or "P2;
if
a two preset unit)
button and
then press the
"R" (Reset)
button. The respective timed output value will
now be displayed and will remain displayed for approximately lOsec.
after release of the last button pushed.
(At this time, the timed output
display mode can be exited, without change, by pressing the "E" button.)
SECOND: Once the timed output is displayed, changing the digit value can
be done by pressing the button directly beneath the digit to be changed.
Each time the button is pressed, the digit will increment by one. Also,
pressing and holding the button down will continuously scroll the digit
from 0 through 9, then back to 0 again. When the desired value for that
digit is reached, release the button. Do this for all the digits to be
changed.
(This value can be set between .01sec. and 99.99sec.)
THIRD: Press the
'E" (Enter)
button to enter the value into the unit's
memory.
AS SOON AS
the "E" button is pressed, this new value is used
as the operating data. If the "E" button is not pressed within lOsec. after
the last digit has been changed, the value will disappear
(go back to nor-
mal display mode)
and the unit will continue to operate on the previous
value. During the displaying, changing, and entering of a new timed
output value, all functions of the unit are operational (i.e.
counting,
resetting, outputs firing, etc.)
TO
ENTER A NEW PRESCALE VALUE * (Dual Preset)
FIRST: Set S9 Prescale
'EN./DIS."
switch to the
"UP"
position
(Enable).
SECOND: Press TS". This will display the prescale value and it will
remain displayed for approximately lOsec. after release of the button.
(At this time, the prescale mode can be exited without change by pressing
the 'E" button.)
THIRD: Once the prescale value is displayed, changing the digit value can
be done by pressing the button directly beneath the digit position to be
changed. Each time the button is pressed, the digit will increment by
one. Also, pressing and holding the button down will continuously scroll
the digit from 0 through 9, then back to 0 again. When the desired value
for that digit is reached, release the button. Do this for all the digits to
be changed.
FOURTH: Press the 'E"
(Enter)
button to enter the value into the unit's
memory.
AS SOON AS
the 'E" button is pressed, this new value is used
as the operating data. If the 'E" button is not pressed within lOsec. after
the last digit has been changed, the value will disappear
(go back to nor-
mal display mode)
and continue to operate on the previous value.
FIFTH: Return S9 to the
'DOWN"
position
(Disable)
if desirable.
TO
ENTER A DECIMAL POINT INTO THE DISPLAY *
The Lynx has the capability of displaying a decimal point in one of five
positions. To turn a decimal point on, first press and release the left most
digit button
(located on the front panel).
This places the Lynx in the deci-
mal point select mode. Then press the digit button which corresponds to
the desired decimal point position. A decimal point will appear to the right
of the digit selected. If the right most digit button
(P1)
is selected, the
decimal point is turned off. The decimal point selection can be done at any
time
(provided that the program disable input is deactivated [open or at
+ 5VDC maximum])
without losing counts or missing preset outputs.
* To enter any new data into the Lynx the "PGM. DIS." terminal must be de-
activated (open or at + 5VDC maximum).
CONNECTIONS & CONFIGURATION SWITCH SET-UPS FOR VARIOUS SENSOR OUTPUTS
COUNT
's
.
s
.
0
13
SWITCH OR ISOLATED
CURRENT SOURCE CONNECTED
(COUNT ON OPENING)
in
•
0
r
a
=
1
2
sl
„
4
l.)
u
—
...
RI
lil
Fil
0
TRANSISTOR
SET-UP
1-07,'
ff.
,i;
'±
1
2
3
OUTPUTS
CURRENT SINK CONNECTED
(COUNT ON CLOSING)
0
hi
6 Y
'8
-
i
A
•
,,
2
i-
.
n
2
'i
m
8 5 t 0.¢
13
lill 111
Li
I®®®
SET-UP
(COUNT
RLC
OLDER
OUTPUT
.-
_,
LI
.
5 2
2 8
CI
A
STYLE
ON FALLING
••
.E
5 2
0 CM
0
C
CURRENT
SENSORS
SRC. CONN.
EDGE)
P.:
in
0 cc
2 t,
2
M
WITH-EF
SET-UP
r771
..
.
L.
-
‘.
5I,
2
3
,.
L.,
a
SEE
RLC
SENSORS
OUTPUT
(COUNT
13
,
=
°
2
Ci
g
cl
ON TURN
z_
,
,-
1
x
I
l'
I
6_
,
WITH
(NPN
TEC
-ON)
z
%
P.,
,
CURRENT
0.C.)
,
SINK
SET-UP
r
c7
7/
^
ff. g
0
R
1
2
3_
,r2 9
5
L,,
NOTE 2
1 7,,=I
,
-
. , ,T,
,f, I i-
1
2
3
Ili1E1
iiiiiiii
tI
l
lifi
RLC SENSOR
PHOTO-ELECTRICS
A
SEE
RR
arIC
,
m
m
N92
9 2
T
h
-
*
SEE NOTE
2
MODELS
PS a
PR
N
r
,-,9
9
,,,
A
SEE
NOTE
2
RPGL, 710,715,730
.r, 0 o
o
*SEE
NOTE
2
LMPC,
RPGH
1----.
SENSOR
WITH
+5v
FOLLOWER
SHIELD
LSC,
NOTE
SENSOR
PSAC,
.------A.-
4
MODELS:
RPGB, RPGC,
SENSOR
ER
OUTPUT
ASTC,
MODELS.
(COUNT
2
WIRE
CURRENT
t1
ON
-
;-
3
g.
8 5
ALE OR
EIDO1=1213
PROXIMITY
SOURCE
CURRENT
0
z
a
'
.,'
i
BLUE
R¢
SENSORS
CONNECTED
FALL)
SET-UP
''
0
I-
7,
4
V
i
n
f ,i
,'
ct
I"
1
2
3
CUITRY
's
0 2
.
0
I3 E1
INTERFACING
WITH CMOS
CIR-
(B
TYPE)
SET-UP
r-71
.,
'
°
i
F .
. , co
=.?,
,-'
±-
i
i
0
A
-
0
0 0 7 O. 4
1
2 3
LI El 111 11
1T{Rii
,
,
,
9 9
,
.
°
O'
El ril
NOTE:
COLLECTOR
FOR DIODE
INTERFACING
WITH TTL
i
z
,,,
,;.
- .
°
cc
2
z,
..,.
.-
2
8
.5 %
1
1211=1E1=1
v
CLAMP
DIODE
SET-UP
1.—.7.‘
.
T.
a
N
r 2
1
2
3
SENSORS
OUTPUT
(COUNT
'S
' i
M
0
0
a
0‘_,
0 lil
ON TURN
E
I-
Z
GI
(PNP
WITH
CURRENT
0.C.)
-OFFI
9
0.
0
O
a.
cc
EI El
o
SOURCE
SET-UP
77
x ff
, ,1
If,
i i
1
2
3
ligm
®®®
liciim
U s 9
2
,
`-;
2 9
zii
TTL
OUTPUT.
WITH OPEN
NEED
,,i)
9 9
NOTE 2
SEE
NOTE: IF
POWER
EQUAL
VOLTAGE.
II
III
RLC
SENSOR
MODELS,
p
SA-
I
PSA- 2
PSA-
3
BRN
EXTERNAL SUPPLY
IS
USED
TO
CMOS CIRCUIT, VOLTAGE
MUST
BE
TO
OR GREATER THAN DC
OUT
TTL CIRCUITS
CIRCUIT
SHOWN FOR STD.
ARE AVAILABLE
OUTPUTS
ELIMINATING
CLAMP.
SENSOR
if
SEE NOTE
NOTES:
1.
SENSOR SUPPLY VOLTAGE AND CURRENT
The +12V sensor supply voltage on the
"DC
OUT"
Terminal is nominal
with + /-25% variation due to line and internal load variations. All
RLC sensors will accomodate this variation.
2.
HI/LO FRO. SELECTION
The
"111/L0 FRQ."
Selection switch must be set on
"LO FRQ."
when
switch contacts are used to generate count input signals. Since the
"LO
FRQ." mode also provides very high immunity against electrical noise
pickup, it is recommended that this mode also be used, whenever possi-
ble, with electronic sensor outputs, as added insurance. The
"LO FRQ."
mode can be used with any type of sensor output, provided count pulse
widths never decrease below 5 milliseconds, and the count rate does not
exceed 100cps.
3.
V
II
_ and
VIH
levels given are nominal values + /-10% when counter volt-
age on
"DC OUT"
Terminal is +12VDC. These nominal values will vary
in proportion to the variations in
'DC OUT"
Terminal voltage, caused by
line voltage and load changes.
4.
When shielded cable is used, the shield should be connected to
"COMM."
at the counter and left unconnected at sensor end.
To Next Page
Loading...
