Avoid intensive skin contact with thread-cutting materials because of the
Use skin protectors with a greasing effect or a suitable hand
Never let the power tool operate unattended. Switch off the power tool and
pull out the mains plug during longer work breaks.
cause hazards which lead to material damage or injury when left unattended.
persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the power tool
safely may not use this power tool without supervision or instruction by a
Otherwise there is a risk of operating errors and injuries.
Only allow trained persons to use the power tool.
the power tool when they are over 16, when this is necessary for their training
and when they are supervised by a trained operative.
Check the power cable of the power tool and extension leads regularly for
Have these renewed by qualifi ed experts or an authorised REMS
customer service workshop in case of damage.
Only use approved and appropriately marked extension leads with a suffi cient
Use extension leads up to a length of 10 m with cable
cross-section 1.5 mm², from 10 – 30 m w
ith cable cross-section 2.5 mm².
cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².cross-section 1.5 mm², from 10 – 30 m w
NOTICE
f thread-cutting material undiluted in the drain system,
Unused thread-cutting material should be handed
in to responsible disposal companies. Waste code for thread-cutting materials
containing mineral oil (REMS Spezial)
, for synthetic materials (REMS
. Waste code for thread cutting materials containing mineral oils
(REMS Spezial) and synthetic thread cutting materials (REMS Sanitol) in spray
cans 150104. Observe the natio
Safety instructions for batteries
WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
See also www.rems.de → Downloads → Operating Instructions and
www.rems.de → Downloads → Safety Data Sheets.
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Power tool complies with protection class II
Not suitable for using outdoors
Switched-mode power supply (SMPS)
Short-circuit-proof safety transformer (SCPST)
Environmentally friendly disposal
Use for the intended purpose
WARNING
REMS electric die stocks for cutting pipe threads and bolt threads for right and left
hand threads (REMS Amigo E).
REMS electric die stocks for cutting pipe threads for right and left hand threads, for
roller grooves (REMS Amigo, REMS Amigo 2, REMS Amigo 2 Compact
All other uses are not for the intended purpose and are prohibited.
Electric die stock, REMS quick-change die heads according to ordered set,
support bracket, operating instructions, steel case.
quick-change die heads according to ordered set, support bracket, Li-Ion battery,
rapid charger, operating instructions, steel case.
REMS Amigo E drive unit 530003
REMS Amigo drive unit 530000
REMS Amigo 2 drive unit 540000
REMS Amigo 2 Compact drive unit 540001
REMS Amigo 22 V drive unit 530004
REMS quick-change die heads see REMS catalogue
REMS dies see REMS catalogue
Plug-on head for button dies see REMS catalogue
Adapter rings see REMS catalogue
Guide sleeves see REMS catalogue
Support brackets (REMS Amigo E, Amigo) 533000
Support brackets (REMS Amigo 2) 543000
Support brackets (REMS Amigo 2 Compact, Amigo 22 V) 543010
Battery Li-Ion 21.6 V, 9.0 Ah (REMS Amigo 22 V) 571583
REMS REG St ¼ – 2" 731700
Dual purpose holder (REMS Amigo E, Amigo, Amigo 2) 543100
REMS eva, ratchet lever 522000
Thread-cutting materials see REMS catalogue
Nippelspanner see REMS catalogue
Steel case with inlay (REMS Amigo E, Amigo) 536000
Steel case with inlay (REMS Amigo 2, Amigo 2 Compact) 546000
Steel case with inlays (REMS Amigo 22 V) 566030
, Machine cleaner
, Machine cleaner 140119, Machine cleaner
Thread diameters Pipes Bolt (both)
REMS Amigo E ⅛" – 1", 16 – 32 mm 6 – 30 mm, ¼" – 1"
REMS Amigo ⅛" – 1¼", 16 – 40 mm 6 – 30 mm, ¼" – 1"
REMS Amigo 2 ⅛" – 2", 16 – 50 mm 6 – 30 mm, ¼" – 1"
REMS Amigo 2 Compact ⅛" – 2", 16 – 50 mm 6 – 30 mm, ¼" – 1"
REMS Amigo 22 V ⅛" – 1", 16 – 32 mm 6 – 30 mm, ¼" – 1"
External threads right- and left-hand
R (ISO 7-1, EN 10226 (DIN 2999, BSPT)), NPT tapered right-handed Taper
Pipe threads parallel G (DIN ISO 228, DIN 259, BSPP) NPSM (with button die)
Threads for electric conduit M × 1.5 EN 60423
Pipe threads tapered standard length
Pipe threads parallel,conduit, bolt 50 mm (with reclamping unlimited)
Nipples and double-nipples
with the REMS Nippelspanner
REMS Amigo E, Amigo 22 V ⅜" – 1"
REMS Amigo 2, Amigo 2 Compact ⅜" – 2"
Operating temperature range
-10 °C – +60 °C (14 °F – +140 °F)
0 °C – +40 °C (32 °F – +104 °F)
Rapid charger 0 °C – +40 °C (32 °F – +104 °F)Rapid charger
Power supply -10 °C – +45 °C (14 °F – +113 °F)
Storage temperature range
1.4. Revolutions of die head
Load-adapted speed (min־¹)
REMS Amigo E, Amigo 35 – 27
REMS Amigo 2, Amigo 2 Compact 30 – 18
REMS Amigo E 230 V~, 50 – 60 Hz; 950 W
110 V~, 50 – 60 Hz; 950 W
REMS Amigo 230 V~, 50 – 60 Hz; 1200 W
110 V~, 50 – 60 Hz; 1200 W
REMS Amigo 2 230 V~, 50 – 60 Hz; 1700 W
110 V~, 50 – 60 Hz; 1700 W
REMS Amigo 2 Compact 230 V~, 50 – 60 Hz; 1200 W
110 V~, 50 – 60 Hz; 1200 W
all-insulated, interference-suppressed
REMS Amigo E, Amigo, Amigo 2 Compact 10 A (B)
REMS Amigo E, Amigo, Amigo 2 Compact 20 A
Intermittent service REMS Amigo E, Amigo,
Amigo 2, Amigo 2 Compact S3 20% (2/10 min)
5
To Next Page
Loading...
