Reznor XL200 - User Manual

TABLE OF CONTENTS
GENERAL INFORMATION ....................................................................1
Applicability ..............................................................................1
Important Safety Information .................................................................1
POWER VENT KITS .........................................................................2
Voltage ..................................................................................2
Kit Selection ..............................................................................2
Venter Assembly ..........................................................................3
Control System ............................................................................4
Venter Adapter ............................................................................4
Power Venter Sequence of Operation ..........................................................5
KIT INSTALLATION .........................................................................5
VENTING ..................................................................................9
Specific Venting Requirements ...............................................................9
Connecting Vent Cap To Double-Wall (Type B) Vent Terminal Pipe ..................................12
Connecting Single-Wall Vent Run to Double-Wall (Type B) Vent Terminal Pipe .........................12
OPERATIONAL TESTING ...................................................................12
REPLACEMENT PARTS .....................................................................13
Revision: X-CA1,2,3,4 (01-22) 136958-A
POWER VENT KIT INSTALLATION FOR DUCT FURNACES
Supersedes: X-CA1,2,3,4 (11-21) 136958-A
OPTIONS CA1, CA2, CA3, AND CA4 FOR MODEL X
AND OBSOLETE MODELS (H)CX, DX, (H)XE, AND (H)CXE
GENERAL INFORMATION
This optional power venter is a motorized vent exhauster designed to permit the installation of a gravity-vented heater
in an area of negative pressure up to 0.15 IN WC or where horizontal venting is required.
Applicability
NOTE: Models with the H prefix are standard and are not listed separately throughout this manual.
The venter assembly in this instruction form is designed to be installed only on the following equipment:
• Models X/DX/HX and CX/HCX: duct furnace
• Models XE/HXE and CXE/HCXE: packaged duct furnace and blower
• Models XL/CXL and XLB/CXLB: fan and blower type unit heaters (power venter cannot be installed on model
XLB/CXLB units in sizes 030–105 when equipped with an optional blower cabinet)
Important Safety Information
• Refer to the installation manual provided with the unit for important safety information.
• Pay attention to all dangers, warnings, cautions, and notes highlighted in this manual. Safety markings should not
be ignored and are used frequently throughout to designate a degree or level of seriousness.
⚠ DANGER ⚠
Improper installation, adjustment, alteration, service, or maintenance can cause property damage,
injury, or death. Read the installation, operation and maintenance instructions thoroughly before
installing or servicing this equipment.

Summary

GENERAL INFORMATION

Applicability

Details on which models the venter assembly is designed for.

Important Safety Information

Crucial safety warnings and precautions for installation and use.

POWER VENT KITS

Voltage and Kit Selection

Lists voltage options and guides for selecting the correct power vent kit.

Venter Assembly

Information on venter assembly dimensions, blower specifications, and electrical ratings.

Control System

Explains the operation of the venter's control system.

Venter Adapter

Information on selecting and using the correct venter adapter.

Power Venter Sequence of Operation

Describes the step-by-step operational sequence of the power venter.

KIT INSTALLATION

Install flue adapter

Instructions for fitting and securing the flue adapter to the furnace.

Install venter assembly

Steps for mounting the venter assembly onto the flue adapter.

Connect electrical wiring

Guidance on wiring the venter assembly according to diagrams.

VENTING REQUIREMENTS

Specific Venting Requirements

Detailed requirements for vent pipe, length, and diameter.

Vent System Joints and Support

Details on joining vent pipes and supporting lateral runs.

Condensation and Vent Terminal

Guidelines on preventing condensation and requirements for vent caps.

Horizontal Vent Terminal Clearances

Minimum clearance requirements for horizontal vent termination.

Vent Pipe Connection Procedures

Steps for connecting vent caps and joining different pipe types.

OPERATIONAL TESTING

REPLACEMENT PARTS

Reznor XL200 Specifications

General

Brand	Reznor
Model	XL200
Category	Fan
Language	English