RFXCOM RFXtrx433XL - User Manual

Copyright 2011-2020, RFXCOM RFXtrx Version 5.68 page 1 / 70
RFXtrx
USB RF transceiver
User Guide
www.rfxcom.com

Summary

RFXtrx General Information

RFXrec433, RFXtrx433, RFXtrx433 E, RFXtrx433 XL Supported Protocols

Lists protocols supported by RFXrec433, RFXtrx433, RFXtrx433E, RFXtrx433XL.

RFXtrx433 Alphabetic Protocol List

Alphabetic list

Provides an alphabetical list of supported devices and their protocol compatibility.

Protocol Sensitivity Influence

Sensitivity influenced by enabled protocols

Installation and Setup

Install the USB driver

Guides on installing the necessary USB drivers for the RFXtrx.

RFXmngr Software Usage

Receiver Configuration

Explains how to configure receiver protocols in RFXmngr.

Transmitter Configuration

Explains how to use RFXmngr to send commands.

Firmware Update Procedure

Update firmware in the RFXtrx

Step-by-step guide to updating RFXtrx firmware.

Update firmware in the RFXtrx step by step

Visual guide on the firmware update process using RFXCOM Flash Programmer.

Harrison Address to Switch Settings

Harrison address conversion to switch settings

Somfy RTS Device Control

Somfy RTS

Details controlling Somfy RTS devices with RFXtrx433E/XL.

Migrating RFY Devices

How to move RFY devices to another RFXtrx433 E or RFXtrx433 XL

Procedure for migrating RFY devices between RFXtrx units.

Funkbus Command Transmission

Transmit Funkbus (Insta, Gira, Jung, Berker)

MCZ Pellet Stove Control

MCZ pellet stove.

Instructions for controlling MCZ pellet stoves with RFXtrx firmware.

RAW Data Transmission

Receive and Transmit RAW data

How to receive and transmit raw data packets.

RFXtrx433 XL P1 Smart Meter Connection

DIY P1 connection for RFXtrx433 XL batch 3618 and 4018

DIY P1 connection guide for specific RFXtrx433XL batches.

DIY P1 connection for RFXtrx433 XL batch 4918 and later

DIY P1 connection guide for later RFXtrx433XL batches.

P1 option PCB Type 1 for RFXtrx433 XL batch 3618 and 4018

Using P1 option PCB Type 1 for specific RFXtrx433XL batches.

P1 option PCB Type 2 for RFXtrx433 XL batch 4918 and later

Using P1 option PCB Type 2 for later RFXtrx433XL batches.

RFXtrx433 XL Teleinfo Connection

Teleinfo option PCB for RFXtrx433 XL batch 4918 and later

Using the Teleinfo option PCB for specific RFXtrx433XL batches.

RFXtrx433 XL Serial Interface Connection

Connection points for a serial interface

Details connection points for a serial interface on RFXtrx433XL.

Firmware Flash Recovery

Recover from interrupted or wrong flash.

Steps to recover the RFXtrx from a failed firmware flash.

Frequently Asked Questions (FAQ)

Receive has stopped suddenly but transmit works.

Troubleshooting steps for reception failure.

Can I increase the receive;transmit range of the RFXtrx?

The RFXtrx USB connection disconnects sometimes.

Solutions for intermittent USB disconnections.

I have a 433.92 MHz sensor;remote but this device is not received.

The wall plug is switched by the remote, the remote is received but the RFXtrx does not switch the module.

Troubleshooting when RFXtrx doesn't switch modules despite remote reception.

RFXCOM RFXtrx433XL Specifications

General

Frequency	433.92 MHz
Interface	USB
Power Supply	USB powered
Operating Temperature	0°C to +50°C
Modulation	ASK
Transmission Range	Up to 100 m
Antenna	External antenna
Supported Protocols	X10, Oregon Scientific, Visonic
Compatibility	Compatible with various home automation software platforms (e.g., Domoticz, Home Assistant, etc.)