What to do if my Rheem Other heater keeps going on and off?
If your Rheem Other heater is turning on and off repeatedly, the issue might stem from several factors. A dirty filter could be restricting water flow, so start by cleaning or replacing it. Also, ensure the water level in your pool is adequate and adjust the external bypass setting. Finally, check and adjust the pressure switch if needed.
Why does my Rheem Other take so long to heat the pool?
If your Rheem Other is taking too long to heat your pool or spa, consider these potential causes. First, verify that the heater is appropriately sized for your pool by calculating its heating capacity or referring to the heater sizing chart. Ensure the filter runs for a sufficient duration by resetting the time clock. Also, a dirty filter can impede heating efficiency, so clean it. Finally, an undersized gas line or meter could be the culprit; refer to the installation instructions for guidance.
How to fix a whining noise in my Rheem Other?
If your Rheem Other is making harmonics or a whining noise, several factors could be responsible. The U.G. may be inoperative; check its movement by placing it in hot water (110°F or higher), and replace it if there's no movement. Debris or restrictions in the system or gas line could also be the cause; locate and remove any obstructions, flush the system, and clean the gas line. Low flow due to scale forming in the heat exchanger is another possibility; clean the heat exchanger and check the pool's pH and total alkalinity.
Why is my Rheem Other producing soot?
If your Rheem Other is experiencing sooting, several factors could be the cause. High flow rates can contribute; reduce them by adding a manual bypass valve and adjusting it until the heater outlet water temperature is between 105°F and 110°F. An inoperative U.G. may also be responsible; check its movement in hot water (110°F or higher) and replace it if necessary. Air starvation or improper venting can also lead to sooting; refer to the installation instructions for guidance. Lastly, insects or debris clogging the burner intake ports could be the issue; clean the burners to resolve this.
What causes pilot outage in Rheem Other?
If your Rheem Other is experiencing a pilot outage or a 'Weak Flame' signal, it could be due to a few reasons. Low gas pressure might be the issue, so try adjusting the gas pressure. A restricted or dirty pilot can also cause this problem, so clean the pilot and/or electrode. If the pilot generator is weak, consider replacing it.
How to prevent scale in Rheem Other exchanger?
If liming or scale is forming in the heat exchanger of your Rheem Other, the cause might be related to the pool water; consult the Water Chemistry guide. Also, too much water bypassing can lead to scale formation; inspect the bypass for movement and replace it if there's no movement. If the U.G. isn't functioning, replace it if it doesn't move when heated.
Why is the flame yellow on my Rheem Other?
If your Rheem Other has a yellow, lazy flame, it could be due to low gas pressure; try adjusting the gas pressure. Alternatively, insects or debris might be clogging the burner intake ports, so clean the burners.
What does “Fan Lockout” signal mean on Rheem Other?
If the combustion fan in your Rheem Other isn't running and you're seeing a 'Fan 5 min Delay' or 'Fan Lockout' signal, the issue could be with the fan relay; consider replacing it. The fan itself might have a loose connection or a failed motor. A burned motor due to incorrect wiring could also be the problem, in which case you should replace the blower. Finally, the air pressure switch might need replacement.
Why is my Rheem Other outer jacket so hot?
If the outer jacket of your Rheem Other is very hot and the paint is blistered, it could be due to a broken refractory caused by shipping damage or improper combustion; replace the refractory panels. Excessive sooting of the heat exchanger could also be the cause; determine the reason for the sooting and correct it.
Why is my Rheem Other gasket brittle and leaking?
If the gasket is brittle and leaking and the Rheem Other heater continues to run after the pump shuts off, it might be due to refractory damage, so replace the refractory. Alternatively, the heater might be sooted; determine the cause of sooting and correct it.
General| Brand | Rheem |
|---|---|
| Model | P-M206 |
| Category | Swimming Pool Heater |
| Language | English |
To Next Page
