EasyManua.ls Logo

Rheem Raypak X94 SR-410 - User Manual

Rheem Raypak X94 SR-410
52 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
X94 Professional
Gas-Fired
Pool & Spa
Heater
This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future
reference.
 A
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette notice
pour réduire au minimum le risqué d’incendie
ou d’explosion ou pour éviter tout dommage
matériel, toute blessure ou la mort.
        
vapors and liquids or other combustible materials in
the vicinity of this or any other appliance. To do so

WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• 
department.
Installation and service must be performed by a

 A
WARNING: If the information in these
       
explosion may result causing property damage,
personal injury or death.
Ne pas entreposer ni utilizer d’essence ou ni d’autres
       
appareil ou de tout autre appareil.
CE FAIRE SI VOUS SENTEZ UNE ODEUR DE
GAS:
• Ne pas tenter d’allumer d’appareil.
• Ne touchez á aucun interrupteur; ne pas vous
      
bâtiment.
•     
gaz depuis un voisin. Suivre les instructions du
fournisseur.
• Si vous ne pouvez rejoinder le fournisseur,
appelez le service es incendies.
      

󰀨


INSTALLATION AND
OPERATION MANUAL
Low NOx Model SR-410
APPROVED
UNCONTROLLED DOCUMENT IF PRINTED

Table of Contents

Questions and Answers

  • M
    Miranda SalinasAug 18, 2025
    Why does my Rheem Raypak X94 SR-410 take so long to heat the pool?
    • H
      huntscottAug 18, 2025
      Several factors can cause your Rheem Swimming Pool Heater to take too long to heat your pool or spa. The heater might be undersized, so you should calculate its heating capacity or refer to the heater sizing chart using the formula: Heating Capacity = Heater output (BTUH) ÷ Pool gallonage x 8.33 (keeping in mind that this calculation doesn't account for heat loss due to weather). Other potential causes include the filter not running long enough (reset the time clock), a dirty filter (clean the filter), or an undersized gas line or meter (refer to the installation instructions).
  • J
    Jimmy WoodsAug 20, 2025
    Why is there sooting in my Rheem Raypak X94 SR-410 Swimming Pool Heater?
    • G
      Gabriel RomeroAug 20, 2025
      Sooting in your Rheem Swimming Pool Heater can be caused by several factors. These include low water temperatures (maintain water body temperatures above 50ºF (10ºC)), air starvation (refer to the installation instructions), improper venting (follow recommended installation instructions), or insects/debris clogging the burner intake ports (clean burners with compressed air gently, avoiding brushes).
  • A
    Arthur LaneAug 23, 2025
    How to fix a whining noise in my Rheem Swimming Pool Heater?
    • A
      Andrew LynchAug 23, 2025
      A whining noise in your Rheem Swimming Pool Heater, also known as harmonics, can stem from a few issues. There might be debris or a restriction in the system (locate and remove the restriction, then flush and clean the system), debris in the gas line (remove the debris or blow out the gas line), or low flow (clean the heat exchanger with a deliming kit (016281F) and check the pool's pH and total alkalinity).
  • L
    Lisa WardAug 26, 2025
    Why does my Rheem Raypak X94 SR-410 Swimming Pool Heater have a yellow flame?
    • M
      Matthew ParksAug 26, 2025
      A yellow, lazy flame in your Rheem Swimming Pool Heater can be caused by a few things. It could be that the air intake is clogged or the fan isn't working right (check for debris upstream of the fan intake and replace the filter if it's dirty). Another cause could be insects or debris clogging the burner intake ports (clean the burners gently with compressed air, but don't use a brush). Finally, the air intake feedback to the regulator might be disconnected (check that the tubing between the air intake adapter and regulator is connected and free of obstruction).
  • P
    pughloriAug 27, 2025
    What causes a 'Fan Lockout' error on my Rheem Raypak X94 SR-410 Swimming Pool Heater?
    • D
      Daniel CochranAug 27, 2025
      If the combustion fan isn't running and you see a 'Fan 5 min Delay', 'Fan Lockout', or 'Fan RPM Fault' message on your Rheem Swimming Pool Heater, the issue could be the fan relay (replace the fan relay), the fan itself (check for loose connections or a failed motor), a burned motor (likely due to incorrect wiring, replace the blower), or a motor control failure (replace the blower).
  • J
    Jesse OwensAug 30, 2025
    What causes scale to form in my Rheem Swimming Pool Heater exchanger?
    • J
      Jesse MorrisAug 30, 2025
      Scale forming in the exchanger of your Rheem Swimming Pool Heater can be caused by pool water (refer to "Water Chemistry" on page 5) or bypassing too much water (inspect the bypass for movement; if there's no movement, replace it).
  • J
    Jonathon RobinsonSep 1, 2025
    Why is the outer jacket of my Rheem Raypak X94 SR-410 so hot?
    • R
      Ryan SteinSep 1, 2025
      If the outer jacket of your Rheem Swimming Pool Heater is very hot and the paint is blistering, it could be due to a broken refractory caused by shipping damage or improper combustion (replace the refractory panels) or excessive sooting of the heat exchanger (determine the cause of sooting and correct it).
  • D
    Donna DennisSep 3, 2025
    Why does my Rheem Swimming Pool Heater turn on for only a few seconds?
    • M
      Miss Kelly BurtonSep 4, 2025
      If your Rheem Swimming Pool Heater turns on for less than 4 seconds without showing an error, it could be due to wiring issues (check for loose or broken wiring, verify continuity of wiring, ground, and the ignition wire), incorrect supply wiring (ensure correct voltage and no power on the neutral line), a PC board short (replace the board if no strength signal is detected), or ignition not being sensed (clean the igniter with a wire brush).
  • J
    Johnathan BrownSep 6, 2025
    Why is the flame visible for only a second on my Rheem Raypak X94 SR-410 Swimming Pool Heater?
    • J
      Jeff WebsterSep 6, 2025
      If the flame is only visible for a split second in your Rheem Swimming Pool Heater, it's likely that the ignition isn't being sensed. Try replacing the ignition wire, checking the connections, and increasing the manifold pressure slightly (turn clockwise).
  • J
    Jordan SolomonSep 8, 2025
    What to do if the valve opens but no flame is visible on my Rheem Swimming Pool Heater?
    • L
      lucaswilliamSep 8, 2025
      If the valve opens but there's no flame visible in your Rheem Swimming Pool Heater, the manifold pressure might be too low. Try increasing the manifold pressure slightly by turning it clockwise.

Rheem Raypak X94 SR-410 Specifications

General IconGeneral
BrandRheem
ModelRaypak X94 SR-410
CategorySwimming Pool Heater
LanguageEnglish

Related product manuals