Ricoh FAX1120L - User Manual

Questions and Answers

J
Jean WebbAug 8, 2025
How to fix 'Cannot open the firmware update file' error on Ricoh FAX1120L Printer?
- E
  Eric WhiteAug 8, 2025
  If you see 'Cannot open the firmware update file' on your Ricoh Printer, ensure that the firmware file (*.brn) and setting file (*.ini) are in the same folder as the update tool, and that you haven't modified the setting file. Also, the path to the update tool might be too long; try saving the update tool in a subfolder directly under the computer’s C: drive for convenience.
K
Kyle JohnsonAug 13, 2025
What to do if the downloaded file is damaged for Ricoh Printer?
- M
  Marcia RyanAug 13, 2025
  If the downloaded file for your Ricoh Printer is damaged, it may be because the firmware update was initiated while the machine was busy faxing, printing, scanning, or copying. Wait for the current job to finish, disconnect any unnecessary cables, and try again. Alternatively, the firmware file itself might be corrupt; in this case, download the firmware package from the website again.
T
Theresa RobersonAug 17, 2025
Why Ricoh Printer says that the machine is not ready?
- C
  Caitlin MooreAug 17, 2025
  If your Ricoh Printer says 'The machine is not ready', it could be due to several reasons. Ensure the USB cable is securely connected between the machine and the computer, and if the issue persists, try another USB cable. Also, verify that the USB printer driver is installed on your computer. The machine might be turned off or have encountered an error; try turning it off, waiting a moment, and then turning it back on. Additionally, check that the IP addresses specified for both the machine and the computer are valid and that the machine is properly connected to the network.
L
Lisa FaulknerAug 21, 2025
What to do if Ricoh Printer says the machine is busy?
- C
  changalexisAug 21, 2025
  If your Ricoh Printer shows 'The machine is busy', it might be because the control panel is in use. Cancel any operations being performed through the control panel, put the machine into standby mode, and then try the update again. Another reason could be an unsent fax in the machine's memory or a received fax waiting to be printed. Send or delete the unsent fax, or print the received fax, and then try again.
J
Jennifer ConnerAug 26, 2025
Why does my Ricoh Printer say 'The models are not the same'?
- J
  Jennifer GriffinAug 26, 2025
  If your Ricoh Printer displays 'The models are not the same' during a firmware update, it means the firmware package you downloaded is not designed for your specific printer model. Each firmware package is designed for a specific model and cannot be used for any other. Check your printer's model and download the appropriate firmware package from the website.
M
mallory60Aug 30, 2025
What to do if Ricoh FAX1120L Printer displays 'LAN Upload: Failed'?
- J
  jkennedyAug 30, 2025
  If your Ricoh Printer displays 'LAN Upload: Failed', it's possible the network cable was disconnected immediately after clicking the [Firmware Update (LAN)] button. To resolve this, turn the printer off, wait a moment, and then turn it back on. Disconnect any unnecessary cables from the printer, and then try again.
C
Corey LloydSep 3, 2025
What to do if Ricoh Printer displays 'USB Upload: Failed'?
- T
  Thomas JenningsSep 3, 2025
  If your Ricoh Printer displays 'USB Upload: Failed', it's possible the USB cable was disconnected immediately after clicking the [Firmware Update (USB)] button. To resolve this, turn the printer off, wait a moment, and then turn it back on. Disconnect any unnecessary cables from the printer, and then try again.

Ricoh FAX1120L Specifications

General

Type	Laser Fax
Print Speed	12 ppm
Resolution	600 x 600 dpi
Paper Size	A4
Dimensions	400 x 400 x 300 mm
Weight	10.5 kg
Modem Speed	33.6 kbps
Transmission Speed	3 seconds per page
Printing Method	Laser
Paper Tray Capacity	250 sheets
Document Memory	Up to 42 pages