What to do if my Riello UPS Sentinel Tower STW 10000 display shows code C05?
If the Riello UPS Power distribution unit display shows the following code: C05, it could be due to the maintenance bypass switch (SWMB) being closed, or the jumper is missing from the terminals “SWITCH BYPASS”. Open the manual bypass switch (SWMB) or insert the jumper to solve this problem.
What to do if my Riello UPS Sentinel Tower STW 10000 Power distribution unit display shows code C01?
If the Riello UPS Power distribution unit display shows the following code: C01, it means that the jumper is missing from the R.E.P.O. connector or it is not inserted correctly. Assemble the jumper or make sure that it is inserted correctly.
What does it mean if my Riello UPS Power distribution unit displays A30 or A32 and won't start?
If the Riello UPS Power distribution unit display shows one or more of the following codes: A30, A32 and the UPS does not start up, it may be because the ambient temperature is below 0°C or there is a fault in heat sink temperature probe. Heat the environment and wait for the heat sink temperature to rise above 0°C before starting the UPS. Alternatively, activate the maintenance bypass (SWMB) if present, turn the UPS off and back on again and exclude the maintenance bypass. If the problem persists, contact the nearest service centre.
What does it mean if my Riello UPS Sentinel Tower STW 10000 display shows F09 or F10?
If the Riello UPS Power distribution unit display shows one or more of the following codes: F09, F10, it may be because the voltage value of phase 1 is not sufficient to pre-load the UPS or there is a fault in the UPS input stage. Wait for the input network voltage values to stabilise within the ranges accepted by the UPS. If the problem persists, activate the maintenance bypass (SWMB) if present, turn the UPS off then back on again, and exclude the maintenance bypass. If the problem continues, contact the nearest service centre.
What does it mean if my Riello UPS Power distribution unit displays codes F11, F14, F17, L06, L07, L08, L09, L14, L17, or L20?
If the Riello UPS Power distribution unit display shows one or more of the following codes: F11, F14, F17, L06, L07, L08, L09, L14, L17, L20, this could be due to anomalous loads applied or a fault in the input or output stage of the UPS. Remove the load. Insert the maintenance bypass (SWMB) if present, turn the UPS off and back on again, and exclude the maintenance bypass. If the problem persists, contact the nearest service centre.
What does it mean if my Riello UPS Sentinel Tower STW 10000 Power distribution unit display shows F19?
If the Riello UPS Power distribution unit display shows the code F19, it indicates a battery charger fault. Open the battery fuse holders (SWBATT) and insert the maintenance bypass (SWMB) if present, then turn the UPS off completely. Turn the UPS back on, and if the problem persists, contact the nearest service centre.
General| Brand | Riello UPS |
|---|---|
| Model | Sentinel Tower STW 10000 |
| Category | Power distribution unit |
| Language | English |
Step-by-step guide on how to safely remove the UPS or Battery Box from its shipping pallet.
Specifies the required conditions for installing the UPS and Battery Box, including ventilation, temperature, and humidity.
Guidance on positioning the UPS or Battery Box, considering space, wheels, and airflow.
Instructions for connecting the UPS to the electrical power supply, with specific guidance for 5-6 kVA models.
Detailed steps for accessing terminals and making electrical connections for the 5 and 6 kVA UPS models.
Detailed steps for accessing terminals and making electrical connections for the 8 and 10 kVA UPS models.
Details the internal fuses used for protection of the UPS's input stage, output stage, and batteries.
Recommendations for external protective devices like magnetothermal switches and fuses for input line protection.
Provides specifications for the minimum cross-section of input and output cables for various UPS models.
Illustrates terminal board connections for 5-6 kVA and 8-10 kVA models, including three-phase and single-phase setups.
Presents schematic diagrams for connecting the UPS to the electrical system under different conditions.
Instructions for installing and connecting Battery Boxes in series for extended runtime.
Explains the need to configure the UPS for Battery Box capacity using software before installation.
Step-by-step instructions for powering on the UPS for the very first time.
Procedure for starting the UPS operation from the mains power supply.
How to power on the UPS and connected equipment using battery power.
Instructions on how to properly shut down the UPS unit.
To Next Page
