What does reference calibration caution mean on Riken Keiki FI-8000 Measuring Instruments?
If the Riken Keiki Measuring Instruments displays '(CAUTION) CHECK REF. CAL', it suggests that zero drift may have occurred or condensation is present. Perform reference gas calibration using a specified reference gas. If condensation occurred inside the product (light source sensor), draw dry air to dry the sensor.
What to do if out-of-specification temperature caution is displayed on Riken Keiki FI-8000?
If the Riken Keiki Measuring Instruments displays '(CAUTION) OUT of SPEC. TEMP', it indicates that the built-in temperature sensor has detected a temperature exceeding the specified range. To resolve this, use the concentration meter within the specified temperature range.
How to fix Riken Keiki Measuring Instruments if the power cannot be turned on?
If the Riken Keiki Measuring Instruments won't turn on, it could be due to several reasons: * **Low Battery:** If you're using an alkaline battery unit, replace all three dry batteries with new ones in a non-hazardous area. For a lithium-ion battery unit, charge the batteries in a non-hazardous area. * **Inadequate Power Switch Press:** Ensure you keep the POWER switch pressed until you hear a beep. * **Improper Battery Installation:** Check that the battery unit is properly attached to the main unit.
Why my Riken Keiki Measuring Instruments showing incorrect reading?
If your Riken Keiki Measuring Instruments shows incorrect readings, consider the following potential causes and solutions: * **Drifting sensor output:** Perform reference gas calibration. * **Incorrect gas selection:** Ensure you have selected the correct measuring and base gases. * **Interference gas:** Remove any interference gases present. * **Pressure issues:** Ensure GAS IN/GAS OUT is at atmospheric pressure. * **Tube issues:** Check for and fix any bended or clogged suction or exhaust tubes. * **Condensation:** Address any condensation inside the suction tube.
What to do if battery error is displayed on Riken Keiki FI-8000 Measuring Instruments?
If the Riken Keiki Measuring Instruments displays '(ERROR) LOW BATTERY', it signifies that the battery level is too low to perform a measurement. If you have an alkaline battery unit, turn off the power and replace the dry batteries with new ones in a non-hazardous area. For lithium ion battery units, turn off the power and charge the batteries in a non-hazardous area.
What to do if low battery voltage caution is displayed on Riken Keiki FI-8000?
If the Riken Keiki Measuring Instruments displays '(CAUTION) LOW BATTEERY', it means the battery level is low. For an alkaline battery unit, turn off the power and replace the dry batteries with new ones in a non-hazardous area. If you're using a lithium-ion battery unit, turn off the power and charge the batteries in a non-hazardous area.
Why communication is not possible with Riken Keiki Measuring Instruments?
If communication with your Riken Keiki Measuring Instruments fails, the main unit's position could be the problem. Try adjusting its position. Alternatively, another device using infrared (IR) might be interfering. Turn off other IR devices or prevent their interference to resolve this.
General| Brand | Riken Keiki |
|---|---|
| Model | FI-8000 |
| Category | Measuring Instruments |
| Language | English |
Details critical safety hazards and necessary countermeasures for hazardous areas.
Outlines potential hazards and warnings for safe operation and handling.
Provides essential precautions for correct and safe usage, including environmental limits.
Summarizes safety specifications, certifications, and critical warnings for use.
Lists and describes the main unit and included standard accessories.
Identifies and explains the function of each control and display element.
Steps and precautions for preparing the meter, including battery and hose setup.
Details on how to perform measurements using automatic or manual suction methods.
Procedure for calibrating the meter using a specified reference gas.
Recommended frequency and procedure for sensor span adjustment.
Addresses issues related to the unit failing to power on.
Addresses caution messages related to reference gas calibration.
Actions to take when a battery error is indicated.
Covers causes and actions for inaccurate measurement readings.
Comprehensive list of the FI-8000's technical specifications.
To Next Page
