Do you have a question about the Rinnai RUC90i and is the answer not in the manual?
Type | Tankless |
---|---|
Fuel Type | Gas |
Maximum BTU Input | 199, 000 BTU/h |
Minimum BTU Input | 15, 000 BTU/h |
Maximum Flow Rate | 9.8 GPM |
Flow Rate (GPM) | 9.8 GPM |
GPM at 35ยฐF Rise | 9.8 GPM |
Venting | Direct Vent or Power Vent |
Gas Type | Natural Gas/Propane |
Input BTU/h | 199, 000 BTU/h |
Temperature Range | 98ยฐF - 140ยฐF |
Electrical Requirements | 120V |
Warranty | 5 years on parts |
Lists indoor and outdoor Rinnai tankless water heater models.
Outlines critical steps to take if a gas leak is detected.
Explains hazard symbols DANGER, WARNING, CAUTION and their meanings.
Provides essential safety practices for operating and maintaining the water heater.
Highlights burn hazards and California Proposition 65 notice.
Details installer requirements and general installation rules.
Lists necessary items for preparing the installation.
Specifies water quality standards to prevent heat exchanger damage.
Discusses air quality and corrosive compounds affecting installation.
Details required clearances for indoor vent terminal installations.
Details required clearances for outdoor vent terminal installations.
Outlines additional clearance rules for various vent termination scenarios.
Provides minimum clearance distances for unit installation.
Advises on protecting the unit and lines from freezing.
Explains how to calculate vent length and adjust DIP switches.
Provides vent length tables specific to Duravent systems.
Checklist to verify the suitability of the installation location.
Instructions for securely mounting the unit to the wall.
Lists certified vent manufacturers and their products.
Details mandatory and prohibited venting practices.
Step-by-step guide for installing concentric vent configurations.
Instructions for setting up the twin pipe PVC/CPVC vent system.
Illustrates flue installation for concentric venting.
Illustrates flue installation for Centrotherm venting.
Introduces the twin pipe PVC/CPVC vent system components.
Emphasizes dangers and requirements for PVC/CPVC venting.
Details requirements and location considerations for PVC/CPVC venting.
Explains how to calculate total system equivalent vent length.
Provides vent length tables for natural gas units.
Provides vent length tables for propane units.
Details the assembly of PVC/CPVC vent and intake piping.
Lists and describes approved vent termination types.
Provides details on the IPEX Concentric Vent Kit assembly.
Specifies required clearances for the IPEX CVK termination.
Shows approved vent configurations and the installation sequence.
Instructions for installing the low profile vent termination kit.
Guidelines for sidewall tee and snorkel vent terminations.
Covers roof terminations and piping for multiple units.
Details pitched roof clearances and joint cementing procedures.
Illustrates acceptable and unacceptable PVC/CPVC elbows for venting.
Lists vent components and their assigned equivalent lengths.
Provides a worksheet for calculating equivalent vent lengths.
Explains condensate formation and provides a checklist for venting and condensate.
Covers requirements for PRVs, isolation valves, and general piping.
Details the installation process for isolation valves and the PRV.
Shows a basic plumbing diagram and its corresponding key.
Instructions for connecting the water heater to the water supply.
Procedures for installing the gas supply line.
Provides tables for sizing natural gas and propane pipes.
Details electrical connection requirements and grounding.
Explains how to adjust settings for high altitude installations.
Covers controller setup, configurations, and placement.
Step-by-step instructions for mounting the temperature controller.
A checklist to ensure all installation steps are completed correctly.
Provides detailed technical specifications for the water heater models.
Shows diagrams and measurements of the unit's dimensions.
Illustrates pressure drop and water flow characteristics.
Presents the electrical ladder diagram for the unit.
Details how to install the recirculation pump and related settings.
Explains the sequence of operation for recirculation modes.
Provides essential facts about the water heater and gas safety procedures.
Guides consumers on safe operation and what to do if gas is smelled.
Explains the features and usage of the MC-91-2 temperature controller.
Details how to set temperature and important safety warnings.
Lists the temperature settings available with controllers.
Explains temperature settings and controller functions without a separate controller.
Describes how to access and display diagnostic information.
Lists diagnostic codes 03 through 16 and their remedies.
Lists diagnostic codes 19 through FF and their remedies.
Outlines annual inspection and maintenance tasks for the appliance.
Covers testing the pressure relief valve and inspecting the flame.
Provides guidance on protecting the unit from freezing and winterizing.
Step-by-step instructions for flushing the heat exchanger.
Instructions for manually draining the water heater and handling freezing.
Details specific state regulations for gas equipment installation.
Lists available replacement parts with corresponding item numbers.
Explains what is covered under the limited warranty and its duration.
Details how to obtain service, warranty exclusions, and limitations.
Explains the process for registering the product to extend labor warranty coverage.