RIOTEC LS6300E - User Manual

Other manuals for RIOTEC LS6300E

Questions and Answers

U
uhuntAug 9, 2025
Why is scanned data incorrectly displayed on the host with my RIOTEC Barcode Reader?
- V
  vjimenezAug 9, 2025
  Incorrect display of scanned data on the host with the RIOTEC Barcode Reader may occur if the proper host type isn't selected. For RS232, ensure that the scanner’s communication parameters match the host’s settings. For keyboard emulation configuration, ensure the system is programmed for the correct keyboard type, and that the CAPS LOCK key is off. Also, ensure editing options (e.g., UPC-E to UPC-A Conversion) are properly programmed. Another potential cause is a mismatch between the scanner’s Keyboard Country setting and the computer’s keyboard setup. To resolve this, set the scanner’s Keyboard Country to the same setting as the keyboard on your computer.
L
Lisa BallAug 14, 2025
What to do if the RIOTEC LS6300E Barcode Reader beeps, but no data is displayed on my computer?
- N
  Natalie LopezAug 14, 2025
  If your RIOTEC Barcode Reader beeps but no data is displayed on your computer, it might be due to an incorrect host type configuration. Ensure the scanner is configured to the appropriate host type by scanning the corresponding programming barcode in the User’s Manual. Another possible reason is that the scanner is configured to send numeric data as KEYPAD NUMERICS, or the Keyboard Country setting is set to UNIVERSAL. To fix this, reconfigure the scanner to send numerics as MAIN KEYBOARD KEYS and set the Keyboard Country setting to the country setting of your computer.
L
lopezrobinAug 19, 2025
Why does the RIOTEC LS6300E Barcode Reader light come on, but the symbol does not decode?
- L
  lyonsedgarAug 19, 2025
  If the light on your RIOTEC Barcode Reader comes on but the symbol does not decode, there could be several reasons. First, the scanner may not be programmed for the correct bar-code type. Refer to the User’s Guide to select the correct interface and ensure the scanner is programmed to read the type of barcode you are scanning. Second, the barcode symbol may be unreadable; check the symbol to ensure it is not defaced and try scanning test symbols of the same barcode type. Finally, the distance between the scanner and barcode might be incorrect; try moving the scanner closer to or further from the barcode.
M
Matthew MartinezAug 23, 2025
Why is some of the barcode data missing when displayed on the host using RIOTEC LS6300E Barcode Reader?
- A
  Austin DavidsonAug 25, 2025
  If some of the barcode data is missing when displayed on the host using the RIOTEC Barcode Reader, the scanner’s transmit speed may be too fast. For RS232, you can adjust the scanner’s transmit speed to resolve this issue.
B
bowmanjohnAug 29, 2025
Why does my Caps Lock LED flicker when I read a bar code using RIOTEC LS6300E?
- R
  Rebecca JacobsonAug 29, 2025
  If the Caps Lock LED on your keyboard flickers when you read a barcode with the RIOTEC Barcode Reader, it is likely because the Keyboard Country you are using requires shifting in and out of the shift Lock mode to send the data properly. This is normal operation. You can reduce the flickering and speed up data transmission by sending numerics as keypad numerics or setting the keyboard country to UNIVERSAL mode.
J
Jill SaundersSep 3, 2025
How to fix a keyboard error on boot when using a RIOTEC LS6300E?
- J
  Joseph MorenoSep 3, 2025
  If your computer gets a keyboard error while booting up when using the RIOTEC Barcode Reader, the scanner might be damaged or no longer functioning. Disconnect the scanner from your computer and use your keyboard only, then reboot your computer. If the keyboard error persists, the scanner may not be the cause of the problem.