7
8
Installation Instruction
Container type
Metal vessel
Wooden, bamboo and
cloth containers
Unusable
Usable
Unusable
Unusable Unusable Unusable
Unusable
Usable
Unusable
Usable
Unusable Unusable
Unsuitable
Usable
Usable
Microwave mode
Baking
mode
Combination
mode
Aluminium-foil paper,
tin-foil paper, etc.
Food fresh-keeping film
crisp plate
It is recommended to use a glass or ceramic container with a wide mouth for
microwave ovens in microwave mode. For example, the use of
necked containers is prohibited. For instance:
Do not drag the crisp plate on the door when taking and placing it, to avoid
damage to the glass.
Place the crisp plate on the cooking layer.
The crisp plate, the inner wall and top of the whole oven chamber are very hot
after use. Do not touch them with hands to avoid scalding.
Clean crisp plate frequently.
When cooking food, place the food in the wavy area in the middle of the crisp
plate. This is to avoid that the food cannot be fully roasted because it enters
the surrounding grooves.
The crisp plate can be used in baking, combination and double-drive baking
and cooking modes.
Note:
In the setting position of the cabinet, set the square hole according to the
installation diagram below, and embed the compact oven with microwave into the
square hole smoothly. Note that tilt placement is not allowed. The specific hole size
(mm) is shown in the following table:
Description
Dimension of completely-nested opening
(WxHxD)
Dimension of half-nested opening
(WxHxD)
W
600
560
1
2
H
395
380
D
450
450
S/N
Installation method:
A. Lay the installation instructions on the bottom of
the cabinet, with the center of the instructions
aligned with the center of the cabinet. The front
edge of the installation instructions shall be aligned
with the front edge of the cabinet. Mark cabinets
according to the position of screws in the
installation instructions. Place the locating plate at
the mark in the correct direction and fix it on the
Locating
plate
Installation
paper
Screw 4.2×12 (3)
Screw 3.5×30 (1)
cabinet with three screws (4.2×12), as shown in Fig. 4. (the protruding edge of the
locating plate faces the front of the cabinet)
B. Put the machine into the cabinet so that the outer frame is about the same
distance from the left and right of the cabinet. Push the machine back into place so
that the locating plate is stuck in the product locating slot. Open the door machine
and fix the product on the cabinet with screws (3.5×30) at the screw position on the
front upper part of the liner.
C. When the cabinet is fully embedded, a fixed board shall be installed on the top of
the cabinet as shown in Fig. 3.
D. The socket shall be conveniently plugged and reliably grounded.
Note: all dimensions in the drawing are in mm.
Fig. 2: schematic diagram of
opening dimensions
Fig. 1: schematic diagram of
overall dimensions
385
5
9
5
3
8
8
H
W
H
W
D
D
F
u
l
ly
embedded
i
n
s
tal
la
t
i
on
H
alf
em
bed
d
ed
in
s
ta
l
lat
i
o
n
Vent hole 200x200
Compact Oven with Microwave Compact Oven with Microwave
解冻
复热
双驱烤
组合
功能
默认
火力
默认
温度
默认
重量
默认时间
火力范围
温度范围
1档：300W
2档：550W
3档：700W
4档：800W
5档：1000W
1档：140℃
2档：160℃
3档：180℃
1档
2档
3档
4档
5档
5档
5档：1000W
2档：550W
/
/
/
/
/
/
20min
30s
20min
20min
1min50s
1min36s
100g
200g
/
/
/
/
3档：
180℃
/
/
/
/
/
5档：
1000W
/
1档
5档
微波
1000W
微波
烤烧
微波
550W
解冻
复热
双驱烤
组合
烤烧
微波
时间范围
加热管
800W
微波变频
器1000W
照明灯
2.5W
搅拌电机
4W
散热风机
18W
重量
范围
功能
5s-30min
1-90min
5s-90min
1-90min
1-90min
/
/
/
/
200g
300g
400g
500g
600g
100g
200g
300g
400g
500g
600g
700g
800g
900g
1000g
1100g
1200g
1300g
1400g
1500g
1600g
1700g
1800g
1900g
2000g
2100g
2200g
2300g
2400g
2500g
2600g
2700g
2800g
2900g
3000g
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
◎
◎
◎
◎
◎
◎
5s-90min
5s-90min
5s-90min
必选
受温度控制
注：
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
To Next Page
Loading...