Assembly instructions
Valdivia
Order No.
1140
Stage 8, the foresail winch
Part Description Material Dimensions No. Note
No. off
8.1 Support rail Spruce 10 x 10 x 58 1
8.2 Bridge piece Plywood, ready made 2 x 21 x 58 1 Sheet E, FS
8.3 Foresail winch 1 N.I.
8.4 Screw plate Plywood, ready made 3 x 21 x 50 1 Sheet C
8.5 Self-tapping screw Steel 2.9 x 9.5 2 FS
8.6 Support block Spruce 10 x 15 x 30 2
8.7 Tongue Plywood, ready made 3 x 10 x 42 2 Sheet C
8.8 Self-tapping screw Steel 2.2 x 9.5 3 FS
8.9 Reinforcement Plywood, ready made 3 x 7 x 15 2 Sheet C
8.10 Tension rail Spruce 2 x 7 x 200 1
8.11 Pulley block Brass 6 x 11.5 1 FS
8.12 Ring-screw Brass 3 x 1.8 x 8 1 FS
8.13 Stop-strip Spruce 2 x 7 x 12 1
8.14 Self-tapping screw Steel 2.2 x 6.5 2 FS
8.15 Winch drum Plastic 38 Ø 1 With 8.3
up the ring-screw 8.12 and fit the block on it.
- Close the loop of the ring-screw again and screw it into the
reinforcement on the tension rail.
- Place the tension rail on the screw plate and drill the holes
as shown in Fig. 99. Establish the position of the stop-strip
8.13 and glue the strip in place. The tension rail can now
be attached to the screw plate using the screws 8.14.
- Fit the winch drum 8.15 on the sailwinch. Place the winch
assembly on the underside of the deck and position the
drum in the centre of the hatch opening. In this position
glue the support rail and the blocks in place. The tension
rail 8.10 must not be glued to the deck girder 5.1 - Fig.
101.
10
- The mountings for the foresail winch are assembled outsi-
de the model - Fig. 99, page 26.
- File a notch in the centre of the support rail 8.1 as shown.
- Glue the bridge piece 8.2 to it leaving a slot into which the
winch 8.3 can be pushed.
- Fix the screw plate 8.4 to the cable end of the winch using
the screws 8.5.
- Glue the blocks 8.6 to the tongues 8.7. Screw the assem-
bly 8.6 / 8.7 to the screw plate 8.4 using the screws 8.8.
- Glue the reinforcements 8.9 to the spruce tension rail 8.10.
Drive in the screw 8.8 to a depth of about 3 mm.
- Drill out the pulley block 8.11 to 2 mm Ø (Fig. 100). Open
Stage 9, the sheet guide system
Part Description Material Dimensions No. Note
No. off
9.1 Guide tube Plastic 3 Ø x 300 1
9.2 Support rail Spruce 10 x 10 x 20 1
9.3 Guide tube Plastic 3 Ø x 150 2
9.4 Sleeve Brass rivet 3 Ø x 17 5 FS
9.5 Swivel Brass 1 FS
9.6 Pulley block Brass 6 x 11.5 1 FS
9.7 Sheet bar Brass rod 1.5 Ø x 140 1 Schooner sail
9.8 Sheet bar Brass rod 1.5 Ø x 160 1 Foresails
9.9 Washer Brass 1.5 x 3.5 2 FS
9.10 Spacer sleeve Brass 2.5 x 5 4 FS
9.11 Split pin Brass 1.5 x 1.5 x 25 6 FS
9.12 Return pulley block Brass 6 x 11.5 2 FS
9.13 Tubular rivet Brass 2.5 x 5 6 FS
9.14 Double block Brass 5 Ø 1 FS
9.15 Split pin Brass 1 x 1.4 x 15 1 FS
9.16 Tubular rivet Brass 1.5 Ø x 10 1 FS
9.17 Jib sheet Beige thread 0.4 Ø x 1.2 m 1
9.18 Crimp sleeve Brass 2.5 x 3 4 FS
9.19 Rubber cord Rubber 1.5 x 0.5 m 1 FS
9.20 Retaining sleeve Brass 2.5 x 8 1 FS
9.21 Schooner sheet Beige thread 0.7 Ø x 0.85 m 1
9.22 Swivel hook Brass 20 long 2 FS
9.23 Main sheet Beige thread 0.7 Ø x 1.8 m 1
9.24 Endless sheet Beige thread 0.7 Ø x 2.0 m 1 Foresails
9.25 Crimp sleeve Brass rivet 2.5 x 3 2 FS
9.26 Swivel hook Brass 14 long 2 FS
To Next Page
Loading...
