Need help?Do you have a question about the Robin EH035 and is the answer not in the manual?
Details the machinery parts and lists the specific engine models covered by the declaration.
Contains the official declaration statement and crucial notes regarding the machinery part's installation and use.
Provides a notice regarding federal and California emission control warranties applicable to engines.
Explains the Air Index level, how it's measured, and its relation to engine exhaust cleanliness.
Outlines the coverage for emission component defects, ensuring conformity with EPA regulations.
Specifies the warranty duration and lists the parts covered under the emission component defect warranty.
Details how to obtain warranty service and lists conditions or parts not covered by the warranty.
Highlights the owner's responsibility for maintaining the emission control system and keeping records.
Explains how to make a warranty claim and the responsibilities of the owner and service center.
Defines the manufacturer's warranty period and coverage for emissions-related parts in California.
Outlines the owner's duties regarding maintenance and presenting the engine for warranty service.
Specifies that engines must be designed and built to conform to Air Resources Board regulations.
Details how warranties apply to parts based on scheduled maintenance and regular inspection.
Lists the specific engine parts that are covered under the emissions warranty program.
Describes the owner's responsibility for performing scheduled maintenance and retaining proof of service.
Advises users to record engine model and serial number, especially when ordering spare parts.
Explains symbols for reading manual, hot surfaces, poisonous gas, refueling, and fire hazards.
Illustrates symbols for engine on/off, starting, and battery status.
Depicts symbols for engine oil level, adding oil, and positive polarity.
Advises on safe handling of exhaust gases to prevent carbon monoxide poisoning.
Outlines precautions for refueling gasoline engines to prevent fires and explosions.
Details measures to prevent fires, including keeping distance from flammables.
Warns about dangers from rotating parts and hot engine components, advising protective measures.
Covers safe handling of electrical components and operating the engine on stable surfaces.
Guides on checking fuel hoses, joints, oil level, and fuel level before operation.
Stresses checking all bolts and nuts for looseness and keeping fins clean.
Advises wearing snug-fitting clothing and checking for potential entanglement hazards.
Illustrates the 'A Type' configuration of the EH025 engine components.
Illustrates the 'P Type' (Pump) configuration of the EH025 engine components.
Illustrates the 'A Type' configuration of the EH035 engine components.
Illustrates the 'P Type' (Pump) configuration of the EH035 engine components.
Shows the location of fuel and oil upper levels and the oil drain screw on the EH035V.
Illustrates the main components of the EH035V engine, including carburetor and starter.
Guides on how to check the engine oil level using the oil gauge and the correct oil capacity.
Instructs on checking the fuel tank level and ensuring the use of automotive unleaded gasoline.
Instructs on setting the stop switch and throttle lever to the correct position for starting.
Details how to adjust the choke lever and prime the carburetor for starting the engine.
Guides on the correct technique for pulling the recoil starter handle to start the engine.
Advises on gradually opening the choke after starting and allowing the engine to warm up.
Describes setting the throttle for the required engine speed and notes on operation.
Outlines the steps to safely stop the engine using the stop switch.
Provides a sequence of checks for when the engine fails to start.
Verifies the engine switch status and checks for adequate compression.
Guides on checking spark plug for fuel saturation and spark strength.
Lists service items to check before running the engine on a daily basis.
Presents a table of periodic maintenance intervals for safe and efficient engine operation.
Details cleaning spark plug deposits and adjusting the electrode gap to specifications.
Provides steps for changing the engine oil, including initial and periodic intervals.
Explains how to adjust the carburetor, noting factory settings and advising caution.
Describes how to increase or decrease engine RPM using the adjusting screw.
Guides on removing, washing, and replacing the fuel filter for optimal performance.
Details the process for removing and cleaning the air cleaner element to maintain engine efficiency.
Advises on retightening loose fasteners and checking for fuel and oil leaks.
Recommends annual replacement of the fuel pipe and immediate replacement if leakage is found.
Explains how to discharge fuel from the tank and carburetor for engines stored over one month.
Details adding oil to the cylinder and cleaning the engine for proper storage.
To Next Page
General
