EasyManuals Logo

Robomow RS622 User Manual

Robomow RS622
59 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #47 background imageLoading...
Page #47 background image
37
Robomow S models
Message
Displayed
Probable Cause/Event Corrective/User Action
Recharge battery
- The maximum operating time has been
reached (displayed in non-Base Station zone).
- Mower is searching for the Base Station but
the battery voltage is too low to continue the
searching process.
- Connect the charger to the mower or place it in the Base
Station for charging.
- Drive the mower manually using the remote control or
carry it by hand for charging in the Base Station.
Start elsewhere
- Drive wheel motors have been working under
a severe load during automatic or manual
operation.
- Check to insure the mower is not stuck, allowing the
drive wheels to slip.
- Check the ground around the mower for holes or
indentations. Fill with dirt and level off.
- Check if the drive wheels are free to rotate and nothing
blocks them.
- Remove the mower away from this particular location
and restart operation.
Start inside
- Automatic operation is initiated while the robot
is placed out of the Perimeter Wire loop.
- Place the mower inside the lawn and press the
button.
Stuck in place
- Robomow got stuck in place. It cannot continue
driving.
- Check the ground for holes or indentions, where the
mower has stopped and fill it with dirt and level off –
especially in the area close to the perimeter, where the
Robomow turns in place.
- Robomow has difficulty to turn in place
because the front wheel is blocked by a hole
or indentation. It caused the mower to turn in
place without detecting wire or bumper.
- Verify that the area is not too steep.
- Work mainly in dry conditions.
- Check if the Perimeter Wire is not too close to the edge
– remove if required.
- Verify that the mowing deck is not set too low.
Sub-Zone X
Problem
- Sub-Zone 1/2/3/4 entry problem.
- The mower either fails to leave / bypass the
Base Station on its way to the Sub-Zone, or
fails to enter the Sub-Zone.
- The mower will try to reach the Sub-Zone every
two hours. If the mower fails to reach the Sub-
Zone within three attempts, it will stay in the
Base Station until the end of current mowing
cycle.
- The mower will not skip to the next Sub-Zone
(if there are any), if it fails to reach the current
one.
- Try to start manual mowing (refer to section 4.5 –
Manual Operation). Check if something disturbs
mower’s driving backwards and/or bypassing the Base
Station. Confirm the mower drives along the perimeter
wire and doesn’t fall off the lawn’s edge, when it departs
from the Base Station.
- Confirm that the mower is able to follow the perimeter
wire along the narrow pass until it reaches the Sub-
Zone. Refer to section 2.2.2 for instructions on how to
set a narrow pass properly.
Switch off
before lifting
- The user carries Robomow manually while the
Safety Switch is On.
- Switch Off the Safety Switch before carrying Robomow.
Waiting for
Signal…
- Robomow has stopped the operation: it does
not detect a signal.
- Check the power to the Power Box.
- It may be an electrical power interruption. There is no
need to do anything. Robomow will renew operation as
soon as power is back.
- תועמשמ שי םא ,ךרוצ ןיא םא

Table of Contents

Other manuals for Robomow RS622

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Robomow RS622 and is the answer not in the manual?

Robomow RS622 Specifications

General IconGeneral
BrandRobomow
ModelRS622
CategoryVacuum Cleaner
LanguageEnglish

Related product manuals