This document is an instruction manual for the ROCHOBBY 1:12 Type82E/87 Kommandeurwagen, a precision-made RC model. It is not a toy and is recommended for users aged 14 and above, with adult supervision required for those under 14. The manual emphasizes safe operation and maintenance, warning against improper use that could result in bodily harm or property damage. It also highlights the importance of replacing damaged components with original factory parts and paying close attention to wiring polarity.
Function Description:
The ROCHOBBY 1:12 Type82E/87 Kommandeurwagen is a highly detailed, realistic scale RC model of the Type82E/87 Kommandeurwagen. It features a 4-channel digital proportional remote control system that allows for steering, throttle control, gear shifting (between 1st and 3rd gear simulation), and switching between 4WD and RWD modes. The model also includes an integrated light control system, enabling users to turn on headlights for normal night driving, linked turn signals, and brake lights at the rear. Anti-aircraft lights can be activated during night light restriction. The doors are designed to open with a built-in spring lock, and the hood can be opened to access the spare tire and battery compartment, which simulates the actual car's fuel tank for convenient battery charging. The model's design includes a servo-operated steering wheel and front wheels for synchronized action, and the interior features simulated fabric texture and soft rubber seats suitable for 1/12 figures.
Important Technical Specifications:
- Length: 339mm
- Width: 139mm
- Height: 139mm
- Ground Clearance: 28mm
- Wheelbase: 202mm
- Departure Angle: 26°
- Approach Angle: 31°
- Radio System: FS-R4A1 three-in-one receiver with ESC and LED light group control board.
- Transmitter: FS-MG41 (4-channel, 2.4GHz ISM, ANT protocol, single antenna)
- Receiver (FS-R4A1):
- Channels: 4
- Light Interfaces: 7
- Input Power: Lipo (2S) / NiMH (5-7Cell)
- BEC Output: 6V/1A
- Continuous/Peak Current: 10A/50A
- Data Output: PWM
- Temperature Range: -10°C to +60°C
- Humidity Limit: 20% to 95%
- Waterproof: PPX4
- Dimensions: 33mm x 30mm x 12mm
- Weight: Approximately 11g
- Transmitter (FS-MG41):
- Channels: 4
- Battery: 4AAA batteries (6V DC 1.5AAA4)
- RF Frequency: 2.4GHz ISM
- RF Power: <20dBm
- Protocol: ANT
- Control Distance: >150m (open, interference-free ground distance)
- Resolution: 1024 levels
- Low Voltage Alarm: <4.2V
- Antenna Type: Built-in single antenna
- Temperature Range: -10°C to +60°C
- Humidity Range: 20-95%
- Dimensions: 118mm x 73mm x 145mm
- Weight: 130g
- Motor: 130 MOTOR (C1281)
- Servo: 9g SERVO (C1280)
- Suspension: Swing axle independent suspension with torsion springs (instead of torsion bars).
- Tires: Simulated 5.25 x 16 off-road tires, fixed with 5 screws.
- Chassis: Solid load-bearing chassis with stamped central ridge tube, high torsional resistance. Central drive shaft and electrical wiring hidden in the ridge tube.
Usage Features:
- Realistic Scale Model: The Kommandeurwagen is designed to be a realistic scale RC model, suitable for enthusiasts.
- Two-Speed Shift: The model features a 2-speed shift to simulate the 1st and 3rd gears of the real car, enhancing driving pleasure off-road.
- 4WD/RWD Switching: The 4th channel on the transmitter allows for switching between 4WD and RWD modes.
- Integrated Light Control: Headlights, turn signals, brake lights, and anti-aircraft lights can be controlled via the transmitter.
- Openable Doors and Hood: The model's doors can be opened with a spring lock mechanism, and the hood opens to reveal a spare tire and battery compartment.
- Detailed Interior: Features simulated fabric texture on door interiors and soft rubber seats, suitable for 1/12 figures.
- Servo-Operated Steering: Steering wheel and front wheels move in synchronized action for realism.
- Removable Plastic Roof: Carved with a fine weave pattern to simulate a cloth canopy, allowing for figures to be placed in the rear when removed.
- Battery Installation: The battery is placed in the battery box under the hood and connected via a plug.
- Transmitter Battery: Requires 4 AAA batteries.
- Binding Process: The receiver automatically enters binding state upon power-on if not connected. The transmitter is put into binding state by pressing the BIND key during power-on.
- ESC Parameter Setting: Running mode (FWD/REV/BRK or FWD/REV), battery type (LiPo or NiMH), and drag brake force (0%, 50%, 75%, 100%) can be set using dial switches on the transmitter.
- Throttle Stick Position: Neutral, top point of forward direction, and top point of backward direction.
Maintenance Features:
- Replace Damaged Components: Emphasizes replacing damaged parts with original factory-parts.
- Polarity Awareness: Special attention should be paid to the polarity of all vehicle wiring.
- Environmental Storage: Store the model indoors, in a climate-controlled, room temperature environment to prevent damage or deformation of plastics due to extreme heat and cold.
- Battery Care: Unplug and remove the battery if the vehicle is not in use for a long time to prevent leakage. Do not charge the battery in the vehicle. Disconnect the receiver battery before turning off the transmitter to prevent unintended operation.
- Radio Range Check: Always check the radio range prior to operation to prevent signal loss or interference.
- ESC Protection: The receiver has multiple prompt functions, including power-on self-check display, overheating alarm, and low/high voltage alarm.
- Motor Direction Check: Ensure all motors operate in the correct direction; adjust if necessary.
- Antenna Placement: Keep the receiver antenna at least 1cm away from conductive materials.
- Easy Suspension Tuning: Torsion springs are used instead of torsion bars, making the front and rear suspension easy to disassemble and change tuning.
Need help?
General
To Next Page
