Rockville USS8 - User Manual

Questions and Answers

K
Karen MaloneAug 16, 2025
How to troubleshoot a Rockville USS8 Subwoofer amplifier that will not power up?
- M
  matthew41Aug 16, 2025
  If your Rockville Subwoofer's amplifier won't power up, begin by checking for a solid ground connection and ensuring the Remote Input (Turn-On) receives at least 3VDC. Verify the (+) terminal has battery power of at least 12V. Inspect all fuses, replacing them if needed. Finally, confirm the Protection LED isn't illuminated; if it is, briefly power cycle the amplifier.
J
Jessica BridgesAug 18, 2025
What to do if my Rockville USS8 has no output?
- L
  lauracervantesAug 19, 2025
  If your Rockville Subwoofer has no output, verify that all fuses are in good condition and that the unit is properly grounded. Ensure the Remote Input (Turn-On) receives at least 3VDC. Check that the RCA audio cables are correctly plugged into the appropriate inputs and inspect all speaker wiring.
N
Nicholas BrownAug 22, 2025
Why does my Rockville Subwoofer have distorted sound?
- T
  Todd HoldenAug 22, 2025
  If you're experiencing distorted sound from your Rockville Subwoofer, check that the Input Level Control is appropriately set to match the signal level of your head unit, keeping it as low as possible. Also, verify that all crossover frequencies are correctly configured and inspect the speaker leads for any short circuits.
K
Katherine CampbellAug 25, 2025
What to do if the Protection LED comes on when my Rockville Subwoofer amplifier is powered up?
- U
  usnowAug 25, 2025
  If the Protection LED illuminates when you power on your Rockville Subwoofer's amplifier, first lower the volume control on the head unit to prevent overdriving. Then, reset the amplifier. If the Protection LED persists, the amplifier may be faulty and require servicing.
S
Sandra PorterAug 27, 2025
Why is my Rockville Subwoofer amplifier getting very hot?
- M
  Matthew PrattAug 28, 2025
  If your Rockville Subwoofer's amplifier is overheating, confirm that the speaker impedance matches the amp model's minimum requirement. Ensure adequate air circulation around the amplifier. Consider adding an external cooling fan if necessary.
P
petermortonAug 31, 2025
How to fix low output on my Rockville USS8?
- M
  Michael WoodsAug 31, 2025
  If your Rockville Subwoofer has low output, try resetting the Level Control. Also, check the Crossover Control settings.
R
Ross JohnsonSep 2, 2025
How to eliminate alternator whine in my Rockville USS8?
- G
  Gina FrenchSep 2, 2025
  If you're hearing alternator whine through your Rockville Subwoofer, check that the RCA grounds are not shorted to the vehicle chassis and ensure the head unit is properly grounded.
J
Joshua BallardSep 5, 2025
How do I reduce high hiss in my Rockville USS8?
- B
  Benjamin SantiagoSep 6, 2025
  To troubleshoot high hiss in your Rockville Subwoofer, disconnect all RCA inputs from the power sub's control panel. If the hiss disappears, plug in the component driving the amplifier and unplug its inputs. Continue this process until you identify the faulty or noisy component. Set the amplifier's input level control as low as possible, maximize the head unit volume (without distortion), and minimize the amp input level for the best signal-to-noise ratio.
P
pageelizabethSep 9, 2025
What causes engine noise (static type) in my Rockville USS8 Subwoofer and how to fix it?
- M
  Megan BeckSep 9, 2025
  Engine noise (static type) in your Rockville Subwoofer is typically caused by poor quality RCA cables picking up radiated noise. Use high-quality cables and route them away from power cables.
H
hunterbrownSep 12, 2025
What causes a squealing noise in my Rockville Subwoofer?
- J
  Jeffrey AlvaradoSep 12, 2025
  If you are experiencing a squealing noise from your Rockville Subwoofer, check for improperly grounded RCA interconnects.

Summary

Introduction

What is included?

Lists all the components that should be present in the package for the USS8 and USS10 amplified subwoofer.

Features

General precautions & Protection Circuitry

What should you do if the POWER STATUS LED turns RED?

Guides users on diagnosing and resolving issues indicated by the red POWER STATUS LED on the amplifier.

Installation precautions

Mounting the subwoofer

Using self-adhesive tape

Instructions for attaching the subwoofer using the supplied double-sided adhesive tape for installation.

Using mounting legs

Instructions for attaching the subwoofer using the provided mounting legs and screws.

Connecting the subwoofer

Dont misuse the level control!

Warns users not to use the input level control as a volume control to prevent distortion and damage.

Panel controls and features

Low and High Level Input Wiring

Troubleshooting

Specifications

Rockville USS8 Specifications

General

Type	Active
Peak Power	800 Watts
Frequency Response	30Hz - 150Hz
THD	< 1%
S/N Ratio	> 90dB
Low Pass Filter	50Hz - 150Hz
Fuse Rating	15A
Subwoofer Size	8 inches
Magnet Weight	30 oz
Voice Coil Diameter	1.5 inches
Enclosure Type	Sealed
Subsonic Filter	20 Hz
Load Impedance	4 Ohm