Roger Technology B70/2DC/BOX - Motor Stop Distance Setting; Photocell (FT1) Mode with Gate Closed; Photocell (FT2) Mode with Gate Closed; Select Number of Motors Installed

EN
51
  
Setting photocell mode during gate closing (FT1)

DISABLED. Photocell is not active or not installed.

STOP. The gate stops and remains stationary until the next command is received.

-11)(-%8)6):)67)8LIKEXIVIZIVWIWMQQIHMEXIP]MJXLITLSXSGIPPMWEGXMZEXIHHYVMRKKEXIGPSWYVI

8)1436%6=78348LIKEXIWXSTWEWPSRKEWXLITLSXSGIPPMWSFWXVYGXIH8LIKEXIVIWYQIHGPSWMRK
when the photocell is cleared.

()0%=)(6):)67)8LIKEXIWXSTWMJXLITLSXSGIPPMWSFWXVYGXIH8LIKEXISTIRW[LIRXLITLSXSGIPPMW
cleared.
 
Photocell (FT1) mode with gate closed

If the photocell is obstructed, the gate cannot open.

The gate opens when an open command is received, even if the photocell is obstructed.

The photocell sends the gate open command when obstructed.
 
Setting photocell mode during gate opening (FT2)

DISABLED. Photocell is not active or not installed.

STOP. The gate stops and remains stationary until the next command is received.

-11)(-%8)6):)67)8LIKEXIVIZIVWIWMQQIHMEXIP]MJXLITLSXSGIPPMWEGXMZEXIHHYVMRKKEXISTIRMRK

8)1436%6=78348LIKEXIWXSTWEWPSRKEWXLITLSXSGIPPMWSFWXVYGXIH8LIKEXIVIWYQIHSTIRMRK
when the photocell is cleared.

()0%=)(6):)67)8LIKEXIWXSTWMJXLITLSXSGIPPMWSFWXVYGXIH8LIKEXIGPSWIW[LIRXLITLSXSGIPP
is cleared.
 
Setting photocell mode during gate closing (FT2)

DISABLED. Photocell is not active or not installed.

STOP. The gate stops and remains stationary until the next command is received.

-11)(-%8)6):)67)8LIKEXIVIZIVWIWMQQIHMEXIP]MJXLITLSXSGIPPMWEGXMZEXIHHYVMRKKEXIGPSWYVI

8)1436%6=78348LIKEXIWXSTWEWPSRKEWXLITLSXSGIPPMWSFWXVYGXIH8LIKEXIVIWYQIHGPSWMRK
when the photocell is cleared.

()0%=)(6):)67)8LIKEXIWXSTWMJXLITLSXSGIPPMWSFWXVYGXIH8LIKEXISTIRW[LIRXLITLSXSGIPPMW
cleared.
 
Photocell (FT2) mode with gate closed

If the photocell is obstructed, the gate cannot open.

The gate opens when an open command is received, even if the photocell is obstructed.

The photocell sends the gate open command when obstructed.
 
Enable close command 6 s after activation of photocell (FT1-FT2)
N.B.: This parameter is not visible if $  or $ is set.

Disabled.

Enabled. When the photocell gate FT1 is crossed, a close command is sent 6 seconds later.

Enabled. When the photocell gate FT2 is crossed, a close command is sent 6 seconds later.
 
Setting motor stop distance

!JEWXIVHIGIPIVEXMSRWLSVXIVWXSTHMWXERGI!WPS[IVHIGIPIVEXMSRPSRKIVWXSTHMWXERGI
 
Select number of motors installed

1 motor.

QSXSVW-14368%289WIXLIWEQIX]TISJQSXSVJSVFSXLKEXIPIEZIW