SYSTEM EFFECT Parameters
33
Parameter Value Explanation
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don’t want to filter out any
high frequencies, set this parameter to
BYPASS.
DELAY 0 TREMOLO
Tremolo is applied to the delay sound.
Parameter Value Explanation
Input
MONAURAL The input is mono-mixed.
STEREO The sound is input in stereo.
Dly Sync
(sync sw) OFF, ON
If this is ON, the delay synchronizes with
the tempo.
Dly Msec
(msec)
Dly Note (note)
1–1300 [msec]
Adjusts the delay time from the direct
sound until the delay sound is heard.
Note
& “Note” (p. 72)
Feedback -98–+98 [%]
Adjusts the proportion of the delay sound
that is fed back into the effect.
Negative (-) settings will invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don’t want to filter out any
high frequencies, set this parameter to
BYPASS.
Trm Switch OFF, ON Switches the tremolo effect on/off
Trm ModWave
Modulation Wave (panning)
TRI Triangle wave
SQR Square wave
SIN Sine wave
SAW1
Sawtooth wave
SAW2
TRP Trapezoidal wave
Trm Sync
(sync sw) OFF, ON
If this is on, the tremolo synchronizes
with the tempo.
Trm Hz
(Hz)
Trm Note (note)
0.05–10.00 [Hz]
Tremolo rate
Note
& “Note” (p. 72)
Trm Depth 0–127 Tremolo depth
2TAP PAN DELAY
Delay sound is heard in the two locations you specify.
Parameter Value Explanation
Dly Sync
(sync sw) OFF, ON
If this is ON, the delay synchronizes with
the tempo.
Dly Msec
(msec)
Dly Note (note)
1–1300 [msec]
Adjusts the time until the second delay
sound is heard.
Note
& “Note” (p. 72)
Feedback -98–+98 [%]
Adjusts the proportion of the delay sound
that is fed back into the effect.
Negative (-) settings will invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don’t want to filter out any
high frequencies, set this parameter to
BYPASS.
Dly 1 Pan L64–63R Stereo location of Delay 1
Dly 2 Pan L64–63R Stereo location of Delay 2
Dly 1 Level 0–127 Volume of delay 1
Dly 2 Level 0–127 Volume of delay 2
3TAP PAN DELAY
Delay sound is heard in the three locations you specify.
Parameter Value Explanation
Dly Sync
(sync sw) OFF, ON
If this is ON, the delay synchronizes with
the tempo.
Dly Msec
(msec)
Dly Note (note)
1–2600 [msec]
Delay time of the third delay sound after
the original sound is heard.
Note
& “Note” (p. 72)
Feedback -98–+98 [%]
Adjusts the proportion of the delay sound
that is fed back into the effect.
Negative (-) settings will invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don’t want to filter out any
high frequencies, set this parameter to
BYPASS.
Dly 1 Pan L64–63R Stereo location of Delay 1
Dly 2 Pan L64–63R Stereo location of Delay 2
Dly 3 Pan L64–63R Stereo location of Delay 3
Dly 1 Level 0–127 Volume of delay 1
Dly 2 Level 0–127 Volume of delay 2
Dly 3 Level 0–127 Volume of delay 3
To Next Page
Loading...
Need help?
General
