Roland GP-16 Service Manual

(Step
2-12:GP-16>
Press [WRITE] key and Data will be transmitted.
Upon
completion of data transmission, the GP-16
returns back to the bulk dump starting status (system
mode).
(Step 2-13:MC-500MK2>
When GP-16 has
finished data
transmission,
press
[STOP] key to exit recording mode.
(Step
2-14:GP-16>
When transfer has completed, press [ESCAPE]
key
and return to the Play mode.
This completes
bulk
data
taransmission.
Data
transfer (MC-500MK2
—
GP-16)
(Step 2-15:MC-500MK2)
Using the
[a
Dial] key or tenkey and [ENTER]
key,
go to the beggining of the measure.
NOTE: Don't start transfer
before putting the GP-16
to ready for reception.
(Step 2-16:GP-16)
Press [SYSTEM]
key to enter the system mode.
(Bit
2
-12:
GP-16)
[WRITE]
7
s
-
9
o
gp-
16
(i,
to
(Bit
2
-13
:
MC-500MK2)
GP-16
7V
<)V
9t~9 9:
[STOP]
t-iBtx,
vu-T
j
y
o
(Bit
2
-14:
GP-16)
$23
-ofzb,
[ESCAPE]
t-tBLXtUt
KCHtito
9k±.X,
^)V9t-
9
<D3IfM7c7o
~
9
(MC-500MK2
—GP-16)
(Bit
2
-15
:
MC-500MK2)
[
«
-Dial]
ttz\t
((-T
>7“
“
1
”)
+
[ENTER]
t~)
it
:
(I
<r>
gp-
i
6
9: KLXfrb,
3§
it
Z
ffl bn
Ltto
(Bit
2
-16:
GP-16)
[SYSTEM]
yXrAt-ncill^o
(Step 2-17:GP-16>
(Bit
2
-17
:
GP-16)
In the system mode, using [FUNCTION]
key, call up 'sTsT
KCl&v^'C,
[FUNCTION] key
7715
<D
the
following parameter
(have
it
appear in the
'*7
9
—
9
—
itVtlTHjLtto
display).
VALUE:
LOADA/ERIFY
The
message "Push
SYSTEM
key!"
will
appear,
7*4
9.
7°Vt
0±fxU
“Push
SYSTEM key”
blinking
in the upper line
of the display.
(Step
2-18:GP-16>
Select LOAD
or VERIFY mode by
using
a
-Dial.
Note: In VERIFY
mode data returning
back to
the
GP-16
are verified.
(Bit
2
-18:
GP-16)
[«
-Dial]
XX-
Vt&TEttto
(LOAD
t
VERIFY
)
it:
“VERIFY”
ZMIRt&m&lt,
t-9%i>t(D
GP-16UH7t^, IELV'7'-* LTW&
*
For details of parameters
refer to the
GP-1 6
Owner's
manual Section
5,
System setting,
6
Data reception
and verification
(Bulk Load
and
Verify)
on
page 50.
(Step
2-19:GP-16)
Press [SYSTEM]
key to put the
GP-16 into ready for
reception status.
Either
of the following messages,
as
appropriate,
will
appear.
(Data
ready-to-receive
state)
*^7
9
-
9
X
t
li,
MU
“H5^v
xtA^coDT/6.
r-
9
(D^in
tmm
)V9
n-
7
7
t
)
P.50”
(Bit
2
-19:
GP-16)
[system]
t-zm
-t,
sit
t,
9
-9-xr
S2<D
«t
7
$
tl
t
to
(r-9%mvsmm)
"LOAD"
"VERIFY
GP-1
B
Jan,
1990
Press
[ESCAPE]
key once
to return
to the System
mode,
or twice
to return
to the Play
mode.
(Step
2-21
:MC-500MK2)
Press
[STOP]
key to
stop the
sequencer.
This
completes
bulk
dump data
receive.
[ESCAPE]
1
KH, 2®
BtttVtX-
KUMO
i
to
(Bit
2
-21 :
MC-500MK2)
[stop]
t~9:Bbx,
y-9-yt-9i'ttbho
HXtzX,
9 r
-
9
12

Roland GP-16 Specifications

General

Brand	Roland
Model	GP-16
Category	Music Pedal
Language	English