Roland GP-16 - Test Mode: MIDI, RRC, and Control Checks; Gain Check Continuation; MIDI Communication Check; RRC Connection Check

GP-16
Jan,
1990
©
d)
Make sure that no at output.
e)
Press
[GROUP A/B] key.
d)
OUTPUT
A b
,
ItitlZtlti:
<£&© t
e)
[GROUP A/B]
f)
Change the
input to rear
INPUT
jack and the
insert the
emptyplug
into front
input jack
g)
Verify
no output when
the emptyplug
is in the
jack.
h)
Connect the
noise meter
and pull out
all input
plug.
i)
This time,
make sure that
noise
meter reads the
following.
Unbalance output
level
—
65dBm
or below
(JIS-A)
Balanced output
level
—
55dBm
or below
(JIS-A)
f)
A^^'JTCIT,
7
n
>
h
INPUT
v-y
v 7
7©
?to
g
)
£7©
rzxtifzftf,
m©
<
&&© t
*mm
o
i) 7
T
X
7
-
9
-
CDiUff
i
?
©
y 7 §|S55'
—
—
65dBm (JIS-A)
JilT
XLR
-55dBm(JIS-A)iAT
'Z'hbz t
zmM-tz
o
Press [FUNCTION
A]
key.
[FUNCTIONS]
Press [FUNCTION
A]
key.
[FUNCTION
A.]
+
9.RRC
check
9
.
RRC
fxy/
©
©Check 1
a)
Connect FC-100MK2
to RRC jack.
OK/IE#
0fx7/
1
a) FC-100MK2
£
RRC
£
,
NG/H#
©Check
2
a)
Input
a
sine
wave (1kHz,
±
OdBm) to front
INPUT jack.
b)
Make sure that
a sine wave
(—
4dBm ±3dB) is being
output
at FC-100MK2's
"SIGNAL OUT
(FOR TUNER)" jack.
©No
change
Display
©A
X V
7
2
a) 7
O
>
h
INPUT
v
f;/
KlEft
r&
lkHz±0dBm£A©©&
o
b) FC-100MK20
“SIGNAL
OUT
(FOR TUNER)”
—
4dBm ±
3dB
$
flh ©
t
Press [FUNCTION
A]
key.
[FUNCTION
A.]
+
-£#1©
10. KEY
and LED
check
i (3 nec
k
©Check 1
a)
Press
buttons one by
one as directed by
the
display a
"Push
* * *
*
key" in sequence.
OK/IE#
10.+
-
Rif
LEDOf x-y^
©A
x
v 7
1
a)
“Push
****
key”
t
ITVAo
NG/JI#
©"GROUP"
indicator,
"OUT
CH" indicator
and "BANK
and NUMBER"
display
will
flash
reciprocally.
Check
that all LEDs
light.
©Display
remains unchanged.
©GROUP
OUT, CH
OUT
Rif
7
dr
7"
7 >
Y(T)
LED
©A
CO
LED
o
Press
[FUNCTION
-
[FUNCTION
A.]
A'
Press
[ESCAPE]
key.
[ESCAPE]
Return
to No.1 Battery
check.
M.%0
WrT.
E
“Battery
check”
To PLAY MODE
7°
u
T
8