Roland HP 3800 - Assembling the KS-3800 Stand for the HP-3800

Assembling
the
KS-3800
Stand
for
the
HP
3800
You
will
need
to
have
a
coin
ready
to
use
when
assembling
the
stand.
Two
people
are
needed
to
carry
out
the
assembly.
Never
attempt
it
alone.
*
To
move
the
main
unit,
be
sure
to
keep
it
level
while
you
lift
it
straight
up.
Be
very
careful,
so
as
to
avoid
getting
fingers
pinched,
or
toes
hurt
by
accidentally
dropping
the
unit.
W Check the parts
Before you begin assembly, check that you have all the following parts.
> Side board (left) --- od
Side
board
(right)
-
1
a”
Pedal
board
og
@
6)
Rear
board
-
sf
®
P
;
Side
cover
--
od
©
y
(@ Long screws (M6 X 60 mm) +- -8
$
Short
screws
(M4
X
15
mm)
=
“4
I.
@
ss
©
Pointed
screws
(4
X
25
mm)
-4
D
@
Connecting
pins
“2
©
@ Philips screwdriver oT
Cord clamps 72 ®© l
E Assembly procedure
Attach the side boards (left and right) to the pedai
board.
Note Extend the pedal cable out from the pedal board,
Note Re sure thot the side boards (left and right ) are oriented correctly: the veneer
surfaces are on the inside.
Note To prevent the side boards from being damaged when the rear
board is fit to them, temporarily tighten the screws on the
side boards.
g Attach the side covers.
Note Be sure that the side covers are oriented correctly:
the rims of the side covers are wider at the back.
@® Use the long screws @ (M6 X 60 mm)
to fasten the side covers to the *
side boards from the inside. Pa
(Use two screws for each side.) ee a
@ Use the long screw @ (M6 X 60 mm) to fasten
the side boards to the pedal board.
(Use two screws for each side.)
To tighten the screws,
slightly lift up the pedal board
so that its threaded holes align
with the holes of the
side boards. ®
Ja
ERE a
eo aa
® Affix the cord clamps ® on the appropriate positions at the back of the rear
board (See the figure below.) then fasten
S
the right and left sides should be up.
@ Fit the rear board into position from the front,
as shown in the figure. Then OA
completely tighten the
screws on the side
boards.
(3) Use the short screws
® (M4 X 15 mm) to .
fasten the rear board <q
to the side boards.
(Use two screws for
each side.)
@) Use the pointed screws
© (4 X 25 mm) to fasten the
rear board to the peal hoard. (Use four screws.)
Ey Attach the piano to the stand.
Note When placing the piano on the stand, be careful not to pinch your fingers. (Avoid
holding the ends of the piano.)
the peda! cord using the clamps.
4@ Plug the power cord into the rear side of
the piano.
(The power cord is supplied
with the piano.)
N
~
g Rotate the adjusting bolt.
Note If the piano is placed on carpeting, rotate the adjusting bolt a little more so it is
properly supported by the floor.
Note When placing the piano in its location, be sure not to pinch the power cord
underneath the piano. ne sas
® Align the screws (one on each side) located on ~~”
the bottom of the piano with the holes in the <
metal fittings, and insert them into the holes.
Slide the piano toward therear so the
screws slide into position. Va <P
@) insert the connecting S f | iN
@ Atter the piano has been assembled
and installed in its location, rotate the
adjusting bolt on the bottom of the
rear board until it completely touches
the floor.
threaded hotes
on the bottom of
the piano through r
the holes in the Cia eel iow
metal fittings of the side boards.
{one on each side}
pins @ into the [N ©
|
|