Roland JUPITER-X Setup Manual

2
JUPITER-X / JUPITER-Xm
Authenticating Your Subscription
You can keep using the tones you installed via Roland Cloud Connect by
periodically authenticating your subscription.
Authentication of your subscription starts automatically once you
connect the WC-1 to the JUPITER-X/Xm.
You should periodically connect the WC-1 to the JUPITER-X/Xm.
You can check the authentication of your subscription as follows.
The remaining number of times you can use the tones you’ve
imported is shown in [MENU] Ó [UTILITY] Ó [WIRELESS ADAPTER] Ó
[W.ADAPTER Info] Ó “Limit.”
Once your subscription is authenticated, “---” is shown as the “Limit.”
* Each time you power up the JUPITER-X/Xm counts as one time.
If you use this instrument 20 consecutive times without
authenticating your subscription, the following message appears
onscreen once you turn on the power.
Connect the WC-1 to authenticate your subscription.
If you use this instrument 30 consecutive times without
authenticating your subscription, the following message appears
onscreen once you turn on the power, and the imported tones are
disabled.
Connect the WC-1 to authenticate your subscription. The tones you
imported are reenabled once you authenticate.
* The WIRELESS ADAPTER parameters are shown only under the
following conditions.
¹ When the WC-1 is connected
¹ When a wave expansion, model expansion or other contents
have been installed via subscription
Your subscription cannot be authenticated in the cases shown
below, and the tones you imported via Roland Cloud Connect
cannot be used.
When the instrument is used for 30 consecutive times without
authenticating the subscription
Note that when the WC-1 is not correctly connected to the network
(via router), authentication is not performed even if you connect the
WC-1 to the JUPITER-X/Xm.
When your yearly Roland Cloud Pro membership has ended
To continue using the contents, renew your subscription.
When your subscription contract has been cancelled
Parameters Shown when Connecting the WC-1
These parameters are related to the WC-1.
[MENU] Ó [UTILITY] Ó [WIRELESS ADAPTER] Ó [W.ADAPTER Info]
These parameters show the connection status of the WC-1.
Parameter Explanation
Version WC-1 version
MAC MAC address
SSID SSID to which the unit connects
Status
WC-1 operating status
Setup Now setting up
Connecting Now connecting to the network (router)
Active WC-1 can be used
Limit
The number of times you can power on this unit before the
tones you’ve installed are disabled
* When the remaining number of times reaches “0,” the installed tones
are disabled, since the subscription was not authenticated.
* Once your subscription is authenticated, the remaining number of
times is initialized and shown as “---”.
You can check the operating status of the WC-1 by looking at the WC-1
operating status LED.
LED Explanation
Lit Connected to network
Blinks slowly Now detecting network
Blinks rapidly Cannot connect to the network (router)
[MENU] Ó [UTILITY] Ó [WIRELESS ADAPTER] Ó [W.ADAPTER Util]
Parameter Explanation
RESET SETTINGS
Initializes the WC-1
* When “RESET SETTINGS” is executed, the WC-1 is disconnected from
the network.
© 2021 Roland Corporation 01

Roland JUPITER-X Specifications

Power

power supply	AC 117–240 V, 50/60 Hz
power consumption	20W

Sound and Effects

preset tones	4, 000 or greater
user tones	256
drum kits	90 or greater

Connectivity

bluetooth profile support	A2DP, GATT
headphones jacks	Stereo miniature phone type, Stereo 1/4-inch phone type
main out jacks	1/4-inch phone type, XLR type

Weight and Dimensions

width	1, 090 mm
depth	447 mm
height	119 mm
weight	16.9 kg