Roland TD-7 Service Notes

Nov.
1992
TD-7
HOW
TO
LOAD
THE
DATA
-
K
The
TD-7
data
which
is
saved on a
sequencer can be
loaded again
onto
the TD-7
using
the
exclusive
MIDI message.
Make
connections
between [MIDI
IN] of
the
receiver (TD-7) and
[MIDI
OUT] of
the
transmitter
(MC500mk2))
as
follows.
[Connection]
TD-7
Receiver
L fz
TD-7
®
r-
^
MIDI
®x
^
X
^7
^
7
•t?
—
o
^
TUI®
cfc
9
[MIDI IN]
t
>
i^fi-#]®
[MIDI OUT]
t
mm
MIDI
OUT
I
MIDI
Sequencer
MC500mk2
Transmitter
< TD-7
>
®Set
the
MIDI
channel
of the
transmitter to the
same
channel as
that
of the
receiver.
1 .
On
the
patch play
screen,
press the
[SYSTEM]
key.
2.
Use
the
[<]
or
[>]
key
to
select
“MIDI” and
press the
[ENTER]
key.
3.
Use the
DATA
knob
to
select
“Inst Tr Ch”,
then use
the
cursor
keys
and
the
DATA
knob
to
set the
MIDI
channel to the
same
channel as
that of
the
transmitter
(MC500mk2).
<TD-7>
©MiDiTi' y^jii^i^^Ltto
1 . ^
7
T
T D
Y
®
liffi-e
[SYSTEM]
T
-
L
^
To
2.
[<].[>]
+-T.
’’MIDI”
[ENTER]
To
3. DATA
':/
-7^
”InstTrCh”^iiO\
tl-yjltDATA-ot^
X\
iiM<MC500mk2>i|WU:T-l’ >T/H-tS^L^To
<
MC500mk2
>
©Use
the
[
a
-Dial] key or
(the [Ten
Key
“1”]
key + the
[ENTER]
key)
to
set at
the first
measure.
Then press
the
[PLAY/SAVE] key
to
transmit
the
data.
<
TD-7
>
©During
the
data
reception, the
message
“Receiving
SysEx” is
displayed.
When
the
data
reception has
been
completed, the
display
automatically
returns to
the
original screen.
<
MC500mk2
>
©Press the
[STOP]
key to
stop the
sequencer.
(When
the data
transmission
has
been completed,
the
operation
automatically
stops
and the
measure blinks.)
Data
load has
now
been
completed.
M I
D
I
Inst.
Tr Ch
:
same MIDI
channel as
that of
the transmitter
: ii(t(fliJ<i:l^i:MIDIT+>:^/l/
< TD-7
>
©Set
the
system
exclusive
reception
switch of the
MIDI
parameter
to
“ON”.
1 .
On the
patch
play
screen,
press
the
[SYSTEM] key.
2.
Use the
[<]
or
[>]
key
to
select
“MIDI”
and press
the
[ENTER]
key.
3.
Use the
DATA
knob to
select
“Sys Exc
Rx”,
then set
the system
exclusive
reception
switch to
“ON”
using the
cursor keys and
DATA
knob.
<TD-7>
ON
lC|9:^L^To
1.
^
7
T T
1/
-r
®
MET
[SYSTEM]
+
-
L ^
To
2.
[<].[>]
T-Ts
’’MIDI”
[ENTER]
To
3. DATA
y-7^X\
Sys
Exc Rx
tl-VJlt
DATA -O
^
^To
M
I D I
Sys
Exc Rx
=
=
ON
<
TD-7
>
©Set
the
system
exclusive
device
number
of the TD-7
to the
same
value
as is
used
at the
time of
data
save
(transmission).
1 .
On
the
patch play
screen,
press the
[SYSTEM]
key.
2.
Use the
[<]
or
[>]
key
to
select
“MIDI” and
press
the
[ENTER]
key.
3.
Use the
DATA knob
to
select
“Device ID",
then set
the
device
ID
number
using
the
cursor keys
and
DATA knob.
<TD-7>
©TD-7 ®
>
X
f-
A
X
:7
X
^
T
-
>
T
•
r
^
<
d'
X I
D T
>
^
^T
-
:7
1 .
/
N°
7
T T
U
-r
®
M®
-r
[SYSTEM]
+
-
L ^
To
2.
[<], [>]
+-T;\
’’MIDI”
[ENTER]
L^To
3. DATA
Device ID
tl-V
Jit
DATA
X\
-r^<TXIDT>^<-^t5^LtTo
I D I
* *
; device
number
[]]i
i.^.i
X
i".
X C'*
“
'*l*. 'I*.
ijc
;
7"
/
^
^
^
T
^
^
Keep
the
performance
stopped
during
this
procedure. MMit.
7.
h
7T$-li-r4ol<>'rT$'-'o
<
MC500mk2
>
©[
a
-Dial]
t
fzU.
([
-f
>
•
T-
’T”]+[ENTER] +-
)
IZh-oX^Xii^ih
[PLAY/SAVE]
LTf-'
-
:7
L
X
T$V^o
<
TD-7
>
©r
—
^ ^^(gT
Six
’’Receiving SysEX
”
t
To
t
S®lWl-7r;®iij®l::M*9
^To
<
MC500mk2
>
®[ST0P]T-^]¥LT>
'>-T>T-^Ih^s6TT$V^o
(
r
-
:7
(Dmmnj
Ltzhmm^tti:).
Ltto
UA±X\
-r-r7D-K^To
7

Roland TD-7 Specifications

General

Display	LCD
MIDI	In, Out, Thru
Effects	Reverb
Sequencer	Yes
Outputs	Stereo output, headphone output
Presets	50 preset kits
Power Supply	AC Adaptor