Roland V-Mixer VM-3100 - VM-3100 Algoriyhms: Center Canceller, EQ, Isolator; Center Canceller and EQ Algorithms; Isolator & Filter Algorithm

VM-3100 List of Algoriyhms
it features a 3-band parametric equalizer connected in series.
Use the insert method with this algorithm.
Center Canceler Equalizer
=z] ere [>| eo LS
R
MONO
CENTER CANCELER
This cuts sounds (such as vocals) placed in the center of the
stereo field.
Position [Pos] (Cancel Position)-50 - +50
This is for finer adjustment of the cut position. This can be
adjusted so that the sound is cut to a great extent.
Lo-F Limit [LoLim] (Low Frequency Limit)
THRU, 20 - 2000 Hz
Hi-F Limit [HiLim] (High Frequency Limit)
1.0 - 20.0 kHz, THRU
These set the upper (Hi-F) and lower (Lo-F) limits of the
frequency range to be cut. When “THRU” is selected, there is
no limit on the frequencies to be cut.
nrg
With this effect, output is converted to mono. Although you can get
a similar effect by using the Anti-Phase function in Algorithm 23
(Isolator + Filter), this algorithm differs in that you can specify the
upper and lower frequency limits of the effect. This is especially
effective when cutting vocals, for exaniple.
nohe
This has no effect when the input sound is monaural. Additionally,
even with stereo input, the amount of cut may differ depending on
the particular recording.
EQ (3-Band Equalizer)
These parameters are the same as those in the ENHANCER
in Algorithm 03 (VOCAL MULTI) (p.13).
Low Type [LType]SHELV, PEAK
Low Freq [LFreq]20 — 2000 Hz
Low Gain [LGain]-12 - +12 dB
Low Q[LQ] 0.3 - 10.0
Mid Freq [MFreq]200 ~— 8000 Hz
Mid Gain [MGain]-12 - +12 dB
Mid Q[MQ] 0.3 - 10.0
High Type [HType]SHELV, PEAK
High Freq [HFreq]1.4 — 20.0 kHz
High Gain (HGain]-12 — +12 dB
High Q [HQ] 0.3 — 10.0
Out Level [OutLv]-60 — +12 dB
23 ISOLATOR & FILTER
This features a 3-band isolator, filter, and low booster that are
connected in series in stereo.
3-band Isolator Filter Low Booster
eet teen tobi?
ISOLATOR(3-Band Isolator)
This effect separates the input sound into three frequency
ranges— High, Mid, and Low—and boosts or cuts each
range.
Level High [Hi Lv]-60 - +4 dB
Level Mid [MidLv] -60 - +4dB
Level Low [LowLv]-60 - +4 dB
Each frequency range—High, Mid, or Low—can be boost or
cut. At -60 dB, the sound becomes inaudible. A level of 0 dB
is equivalent to the input level of the sound.
AntiPhs Md [PhsMd]
(Anti-Phase Middle Switch) OFF, ON
AntiPhs Md Level [PhsML]
(Anti-Phase Middel Level)0 - 100
AntiPhs Lo [PhsLo] (Anti-Phase Low Switch)
OFF, ON
AntiPhs Lo Level [PhsLL] (Anti-Phase Low Level)
0-100
This turns the Anti-Phase function on and off and sets level
settings for the low and mid frequency ranges. When turned
on, the phase from the opposite stereo channel is inverted
and added to the signal. Depending on the level settings, you
can achieve an effect that sounds as if only a particular part is
being boosted. (This is effective only in stereo.)
yore
Functions featured in machines consider standard equipment for
remix artists and pro DJs have been carefully analyzed and
reproduced. Ordinary equalizers allow some sound to persist even
when the gain is turned down all the way. In contrast, the Isolator
completely cuts off the sound. By switching the effect on and off,
and by changing levels in real time, you can have the sound of
30