Roland V-Mixer VM-3100 - Points for Better Mixing: EQ and Routing; Equalizer Functions and Settings; EZ Routing Configuration and Management

m@ EQUALIZER
Calling up the Equalizer screen with the knobs
1. Press [SYSTEM].
2. Press [{ 4 ] to select “EQ ScreenJump.”
3. Rotate the VALUE dial to set this to “ON.”
* When set to “ON,” rotating the [HIGH], [MID], ar [LOW]
knobs calls up the “(EQ)” screen.
* When set to “OFF,” the “(EQ)” screen is nat displayed.
With the “(EQ)” screen displayed, carry out the following.
- Press [LEVEL METER].
2. Press [F1-F4 ON/OFF].
3. The functions appear in the display.
4. Press [F4] (EQ).
ASSAD SL TN TT ET I
Adjusting the equalizer’s frequencies and Q
setting
1. Call up the Equalizer screen.
2. Press [SELECT] for the channel whose equalizer you wish to
adjust.
3. Usethe[ T),[ 1], [], and [ L ] buttons to select the
frequencies to be adjusted, Q, and gain.
4. Rotate the VALUE dial to adjust the values.
AAA TR ET POL OR IT
Turning the equalizer on and off
1. Call up the Equalizer screen.
2. Press [F4] (>OFF) or [F4] (>ON).
ESE ET LE NTE ETI
Copying equalizer settings to another channel
1. Call up the Equalizer screen.
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F3] (COPY).
4. Press [<— ] to select “Source.”
5. Rotate the VALUE dial to select the source channel you
wish to copy from.
6. Press [— ] to select “To.”
7. Rotate the VALUE dial to select the destination channel you
wish to copy EQ settings to.
8. Press [ENTER/YES] two times.
RARE ER ELT Re EIN LO AE
Saving equalizer settings to the Library
1, Call up the Equalizer screen.
2. Press [SELECT] for the channel on which you want to save
these settings.
3. Press [Fl-F4 ON/OFF]. The functions appear in the display.
4. Press [F2] (SAVE).
5. Press [T ] to select “No.”
6. Rotate the VALUE dial to select the position in the library
where you want to save these settings.
7. Press [1] to select “Name.”
8. Use the { — ] and [— ] buttons and the VALUE dial to input
the Name.
* By pressing [F1] (Ins). you can insert one character at the
cursor position; press [F2] (Del) to delete one character at the
cursor position.
9. Press [ENTER/ YES] two times. Alternatively, you can press
[F4] (EXEC) followed by [ENTER/ YES].
I REE A NTT,
Calling up various equalizer settings
1. Call up the Equalizer screen.
2. Press [SELECT] for the channel on which you want to load.
3. Press [F1-F4 ON/OFF]. The functions appear in the display.
4. Press [F1] (LOAD).
5. Rotate the VALUE dial to choose the Library number you
want to load.
* Press [F1] (>Pre) or [F2] (>User) to go to the beginning Preset
or User numbers.
6. Press [ENTER/YES] two times.
ot
a a ee TE
Deleting Unneeded Equalizer Settings (Delete
EQ Library)
1. Call up the Equalizer screen.
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press {F4] (DEL).
4. Rotate the VALUE dial to select the Library number to you
want to delete.
5. Press [ENTER/YES] twe times.
m EZ ROUTING
Calling up various routings
1. Press [EZ ROUTING].
2. Rotate the VALUE dial to display the name of the abailable
routing settings.
3. Press [ENTER/ YES].
Changing routings between inputs and
channels
1. Press [EZ ROUTING}.
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F1] (IN).
4. Use the f — ] and [ — ] buttons to select the channel number
“Ch*t=" (where ** is the channel number).
5. Rotate the VALUE dial to select the INPUT that your signal
is coming from.
ELE LEELA LENE NEE ELIE. IL TIENT TTS
Selecting the internal bus function
1. Press [EZ ROUTING].
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F2] (OUT).
4. Use the [ T ] and [ £ } buttons to select the internal bus name
“Bus */*=” (where */* is the internal bus number).
5. Rotate the VALUE dial to select the internal bus function.
”"SND-M (Send Monaural)”
"SND-S (Send Stereo)”
“BUS (Bus)”
* Settings affecting transmission of signals from channels to
internal buses set to "SND-M" or “SND-S" are made in the
“(AUX SEND)” screen (press [AUX SEND)).
* Settings affecting transmission of signals from channels to
internal buses set to “BUS” are made in the “(BUS ASSIGN)”
screen (press [BUS ASSIGN)).
Ee ee Ae I DE eT OTE ND
Changing routings between OUTPUT ,
MONITOR (the internal bus), and other
destinations
1. Press [EZ ROUTING].
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F2] (OUT).
4. Use the [ — ] and [— ] buttons to select the OUTPUT
“Aux=,” Bus=, “DoutA=,” or “DoutB=.”
5. Rotate the VALUE dial to select the internal bus you want
routed to OUTPUT.
SRS EET, SEEN
Routing effects
1. Press [EZ ROUTING}.
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F3] (FX).
4. Use the [ T ] and [ 4 } buttons to select “Location” (location
in the mixer) and “Patch” (the patch number).
* On the VM-3100Pro, use the [ — ] and | - ] buttons to switch
between Effect and Effect2).
5. Rotate the VALUE dial to select the location in the mixer
and patch number.
“IMPORTANT NOTES atc.
aa
pre)
3
ed
ib
=
~
A
bee ah}
fos:
psig
=
wy
—
- What is the VM-2100 Series
V-Mixing Station? ©
Par Names -
Trying Out the ¥VM-3100
Digital Mixer Workbook
51