44
Algorithm List
Vocal Multi
This feature provides a multi-effect suited for vocals.
fig.08-30
Parameter (full name) Setting Function
NS (Noise Suppressor): Mutes noise in the silent mode.
Sw (Switch) On, Off Turns the noise suppressor on or off.
Thresh (Threshold) 0–100 Sets the level to start muting noise.
Release (Release) 0–100 Sets the time over which the volume will drop to 0 after the noise starts being muted.
Lmt (Limiter / De-esser): Suppresses signals at High levels to control distortion /
Suppresses the annoying s-consonant.
Sw (Switch) On, Off Turns the limiter/de-esser on or off.
Mode (Mode) Limiter, De-esser Selects limiter or de-esser.
Thresh (Limiter Threshold) 0–100 Sets the volume at which sound distortion starts being suppressed.
Release (Limiter Release) 0–100 Sets the time until when the limiter will turn off after the input level falls the limiter Threshold
(Thresh).
Level (Limiter Level) 0–100 Sets the volume of the limiter sound.
ENH (Enhancer): Accentuates the sound and push the sound forward.
Sw (Switch) On, Off Turns the enhancer on or off.
Sens (Sense) 0–100 Sets the degree of the enhancer effect desired.
Freq (Frequency) 1.0–10.0 kHz
Sets the frequency at which the enhancer effect starts working.
MixLvl (Mix Level) 0–100 Sets the amount of the enhancer sound should be mixed into the direct sound.
Level (Level) 0–100 Sets the volume of the enhancer sound.
EQ (Equalizer)
Sw (Switch) On, Off Turns the equalizer on or off.
Low Gain (Low Gain) -12– +12 dB Sets the boost/cut amount in the low frequency band.
Low Freq (Low Frequency) 20 - 2000 Hz Sets the center frequency in the low frequency band.
Low Q 0.3–10.0 Sets the width of the area around the low frequency that will be affected by the gain settings. *1
Low Type Shlv, Peak Sets the type of the low frequency band equalizer (Shlving type or peaking type).
Mid Gain (Middle Gain) -12– +12 dB Sets the boost/cut amount in the middle frequency band.
Mid Freq (Middle Frequency) 200–8000 Hz Sets the center frequency in the middle frequency band.
Mid Q (Middle Q) 0.3–10.0 Sets the width of the area around the middle frequency that will be affected by the gain settings.
High Gain -12– +12 dB Sets the boost/cut amount in the High frequency band.
High Freq (High Frequency) 1.4–20.0 kHz Sets the center frequency in the High frequency band.
High Q 0.3–10.0 Sets the width of the area around the High frequency that will be affected by the gain settings. *1
Hi Type (High Type) Shlv, Peak Sets the type of the High frequency band equalizer (Shlving type or peaking type).
Level (Output Level) 0–100 Sets the volume after passing through the equalizer.
Pshift (Pitch shifter): shifts the pitch.
Sw (Switch) On, Off Turns the pitch shifter on or off.
Chromatic Pitch -12–12 Pitch variation (by semitone)
Fine Pitch -100–100 Pitch variation (by cent)
FX Lvl (Effect Level) -100–100 Sets the volume of the pitch shift sound.
DirLvl (Direct Level) -100–100 Sets the volume of the direct sound.
Input L
Input R
Output L
Output R
Noise
Suppressor
Limiter/
De-esser
Enhancer
3BAND EQ
Delay
ChorusPitch Shifter
Cutting distortion in vocals
Limiter can be used to suppress signals at a High level to prevent sound distortion. To do this, follow the steps below:
Mode (Mode): Limiter
Limiter Threshold (Thresh): Sets the volume at which sound distortion starts being suppressed.
Limiter Release (Release): Determines the time that elapses before the input level becomes off after it drops below the Limiter Threshold.
Limiter Level (Level): Decides the volume after passing through Limiter.
Cutting the sibilant sounds of a voice.
De-esser can be used to cut off sibilant sounds contained in vocal sounds to achieve softer sound quality. To do this, follow
the steps below:
Mode (Mode): De-esser
De-esser Sense (Sens): Sets the degree of the De-esser effect.
De-esser Frequency (Freq): Sets the frequency at which De-esser effect starts working.
VS-2000_e.book 44 ページ ２００５年１２月１２日 月曜日 午後４時５４分
To Next Page
Loading...
