Roland VS-2000 - Page 97

97
MIDI Implementation
4. Bulk Dump
VS-2000 can transfer and receive the scenes, the EZ ROUTING User Templates and the User
Effect Patches by bulk dump.
In order to make bulk dump transmit, a transmitting function is performed on UTILITY-
MIDI BULK DUMP screen.
In order to make bulk dump receive, after changing into a reception standby state on
UTILITY-MIDI BULK DUMP screen, the bulk dump which the VS-2000 outputted
beforehand is sent to the VS-2000.
■ Address Block
+—————————————————————————————————————————————————————————————————+
| Start | |
| address | Contents and remarks |
|=============+===================================================|
| 10 00 00 00 | SCENE #1—1 |
: :
| 10 00 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
| 10 01 00 00 | SCENE #1—2 |
: :
| 10 01 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 10 0F 00 00 | SCENE #1—16 |
: :
| 10 0F 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
| 10 10 00 00 | SCENE #2—1 |
: :
| 10 10 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 10 5F 00 00 | SCENE #6—16 |
: :
| 10 5F 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
| 11 00 00 00 | EZ ROUTING USER TEMPLATE #00 |
: :
| 11 00 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
| 11 01 00 00 | EZ ROUTING USER TEMPLATE #01 |
: :
| 11 01 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 11 13 00 00 | EZ ROUTING USER TEMPLATE #19 |
: :
| 11 13 7F 7F | |
|—————————————+———————————————————————————————————————————————————|
| 12 00 00 00 | EFFECT USER PATCH #000 |
: :
| 12 00 01 7F | |
|—————————————+———————————————————————————————————————————————————|
| 12 00 02 00 | EFFECT USER PATCH #001 |
: :
| 12 00 03 7F | |
|—————————————+———————————————————————————————————————————————————|
: :
|—————————————+———————————————————————————————————————————————————|
| 12 03 0E 00 | EFFECT USER PATCH #199 |
: :
| 12 03 0F 7F | |
+—————————————————————————————————————————————————————————————————+
5. V-LINK TRANSMITTED DATA
The following control command will be transmitted while V-LIN function is activated.
■ CHANNEL VOICE MESSAGES
● CONTROL CHANG
❍ Controller Number 0
This is used to switch image banks. (MIDI ch.=1 fixed)
In the V-LINK activated mode, while AUTOMIX is playing, this is transmitted when the
current time coincides with the pre-registered time for switching image bank.
Status
Second Third
B0H 00H mmH
mm = Bank Nunber : 00H - 7FH (1 - 128)
❍ Controller Number 1
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Brightness
(MIDI ch. is fixed at 1).
Status
Second Third
B0H 01H mmH
mm = Control Value: 0H - 7FH (0 - 127)
❍ Controller Number 5
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Dissolve Time
(MIDI ch. is fixed at 1).
Status
Second Third
B0H 05H mmH
mm = Control Value : 0H - 7FH (0 - 127)
❍ Controller Number 7
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Color Cb
(MIDI ch. is fixed at 1).
Status
Second Third
B0H 07H mmH
mm = Control Value : 0H - 7FH (0 - 127)
❍ Controller Number 10
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Color Cr (MIDI
ch. is fixed at 1).
Status Second Third
B0H 0AH mmH
mm = Control Value : 0H - 7FH (0 - 127)
❍ Controller Number 11
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to T Bar (MIDI ch.
is fixed at 1).
Status
Second Third
B0H 0BH mmH
mm = Control Value : 0H - 7FH (0 - 127)
❍ Controller Number 72
If the V-LINK function is On and the UTILITY V-LINK SETUP screen's FADER ASSIGN Sw
is also On, this message is transmitted when you operate a fader assigned to Playback
Speed (MIDI ch. is fixed at 1).
Status
Second Third
B0H 48H mmH
mm = Control Value : 0H - 7FH (0 - 127)
VS-2000_e.book 97 ページ ２００５年１２月１２日 月曜日 午後４時５４分