Rommelsbacher OP 700 - User Manual

Questions and Answers

A
Amy BennettAug 7, 2025
What to do if my Rommelsbacher Kitchen Appliances cannot be switch on?
- K
  Kimberly ParkerAug 7, 2025
  If your Rommelsbacher Kitchen Appliance isn't turning on, there are several things to check: * Ensure the locking mechanism is correctly locked. * Verify the appliance is properly plugged in and test the socket with another device. * Inspect the power cord and plug for damage. * Confirm the appliance is assembled correctly and the lid is correctly seated on the seed container. * Check the micro switch at the rear for any clogs. If the appliance has been used for an extended period, allow it to cool down, as the overheating protection may have been activated.
N
Norma BrownAug 10, 2025
Why is my Rommelsbacher OP 700 Kitchen Appliances making a loud noise?
- J
  Joshua ThompsonAug 11, 2025
  If your Rommelsbacher Kitchen Appliance is making loud noises, consider these potential causes and solutions: * Ensure the appliance is correctly assembled. * Check for and remove any foreign materials in the material being pressed. If there is a blockage, refer to the section on 'Clearing a screw conveyor blockage'. * If the material is too moist, dry it in the oven. If it's too large, crush it again. * Apply a drop of oil on the sealing.
V
vroweAug 15, 2025
What to do if my Rommelsbacher OP 700 Kitchen Appliances stops during operation?
- B
  bassnormaAug 15, 2025
  If your Rommelsbacher Kitchen Appliance stops during operation, consider the following: * Check for any blockages and clear them. Refer to the section on 'Clearing an screw conveyor blockage'. * Make sure there is enough material in the hopper and that it isn't jammed. Refill if necessary, and then restart the appliance. * Ensure the lid is firmly pressed. If the appliance has been running for a long time, the overheating protection of the motor may be activated.
C
Catherine HarrisAug 19, 2025
Why is my Rommelsbacher Kitchen Appliances producing no yield or unsatisfying results?
- N
  Nathaniel BensonAug 20, 2025
  If you're experiencing no yield or unsatisfying results with your Rommelsbacher Kitchen Appliance, consider the following: * Verify that you are using the correct screw conveyor. * Check the screw conveyor or casing for blockages. * Ensure the screw conveyor isn't jammed, possibly due to material that's too moist. * The material to be pressed may not contain enough oil.
C
Christopher TurnerAug 23, 2025
How to attach seed container to Rommelsbacher OP 700?
- C
  Calvin RichardsonAug 25, 2025
  If the seed container cannot be attached to your Rommelsbacher Kitchen Appliance: * Ensure the locking mechanism is slid to the stop on the left-hand side, to the closed padlock symbol. * Move the screw conveyor casing to and fro to lock it correctly.
J
Jamie MooreAug 28, 2025
What to do if Rommelsbacher OP 700 Kitchen Appliances doesn't stop when seed container is empty?
- J
  jamesadamAug 28, 2025
  To resolve this issue with your Rommelsbacher Kitchen Appliance, start the voltage adaptation programme (refer to point 'Voltage adaption – Activating the auto cut-off function' on page 31). This is necessary if the appliance was not adapted to your local electricity supply.
K
Kelly WongSep 1, 2025
Why screw conveyor casing cannot be disassembled easily on Rommelsbacher OP 700 Kitchen Appliances?
- J
  Jill StricklandSep 1, 2025
  If the screw conveyor casing of your Rommelsbacher Kitchen Appliance is difficult to disassemble, it may be due to foreign matters blocking the screw conveyor. Remove the foreign matters, referring to the section on 'Clearing a screw conveyor blockage'.