EasyManua.ls Logo

ROTORCOMP EVO6 - User Manual

Default Icon
36 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
ROTORCOMP VERDICHTER GmbH | A Member of BAUER GROUP
[en] 07/2020
SCREW COMPRESSOR AIR ENDS
EVO2, EVO3 / EVO3-G, EVO6 / EVO6-G, EVO9 / EVO9-G,
EVO15 / EVO15-G, EVO28 / EVO28-G, EVO42 / EVO42-G
OPERATING MANUAL

Table of Contents

Questions and Answers

  • T
    Troy RussoSep 23, 2025
    What to do if leaks in system of ROTORCOMP EVO6 Compressor?
    • M
      Matthew ChenSep 23, 2025
      If there are leaks in the system of your ROTORCOMP Compressor, check and seal them off.
  • X
    xrayAug 23, 2025
    What to do if the safety valve blows off on my ROTORCOMP Compressor?
    • J
      Jason SantiagoAug 25, 2025
      If your ROTORCOMP Compressor's safety valve blows off, the safety valve might be defective and needs replacement.
  • A
    alexandraandersonAug 25, 2025
    Why does my ROTORCOMP EVO6 Compressor system not start?
    • P
      Pamela JohnsonAug 26, 2025
      If your ROTORCOMP Compressor system does not start, the cause might be a lack of electricity. In this case, you should check the power supply.
  • R
    ramosdouglasAug 27, 2025
    Why is there oil in the compressed air from my ROTORCOMP Compressor?
    • T
      Thomas JonesAug 27, 2025
      If there is oil in the compressed air of your ROTORCOMP Compressor, it could be due to the fine separator cartridge being defective. Check the cartridge and replace it if necessary.
  • T
    Taylor CannonAug 27, 2025
    Why is there no or insufficient feed quantity from my ROTORCOMP EVO6?
    • S
      smithsusanAug 27, 2025
      If your ROTORCOMP Compressor experiences no or insufficient feed quantity, the intake filter might be soiled. Replace the filter insert to resolve this issue.
  • L
    Lisa HuntSep 16, 2025
    What to do if minimum pressure valve jammed and ROTORCOMP EVO6 doesn't switch off automatically?
    • D
      Dr. Laura TaylorSep 16, 2025
      If your ROTORCOMP Compressor is not discharged during continuous operation, or doesn't switch off automatically during intermittent operation, and the minimum pressure valve is jammed, check the minimum pressure valve for smooth movement and ensure it moves smoothly if necessary.
  • S
    shortjustinSep 13, 2025
    What installation errors cause overheating in my ROTORCOMP Compressor?
    • R
      Rachel KrauseSep 13, 2025
      If the combistat switches off due to excessively high temperature in your ROTORCOMP Compressor, the issue might stem from incorrect installation, such as inadequate room ventilation, blocked exhaust air, or a thermal short circuit. Observe the installation recommendations for the system.
  • S
    Sandra Carr PhDSep 14, 2025
    Why doesn't the control valve close in my ROTORCOMP Compressor?
    • A
      Adam HobbsSep 15, 2025
      If your ROTORCOMP Compressor's control valve does not close, check the setting of the pressure switch or control valve.
  • G
    garciahollySep 5, 2025
    What should I do if the oil cooler is causing my ROTORCOMP Compressor to overheat?
    • R
      rbrennanSep 5, 2025
      If the combistat switches off due to excessively high temperature on your ROTORCOMP Compressor, the oil cooler may be soiled. Clean the oil cooler on the air side, and if necessary, clean it on the oil side as well.
  • A
    Antonio CarterSep 3, 2025
    How to fix a faulty thermostat causing high temperature shutdown in my ROTORCOMP EVO6?
    • J
      jessicahernandezSep 3, 2025
      If the combistat switches off due to excessively high temperature in your ROTORCOMP Compressor, it might be due to a faulty thermostat. Replace the thermostat to resolve this.

Summary

Foreword

1.5.2 Purpose

Details the intended use of screw compressor air ends for atmospheric air compression.

1.6 Warranty information, liability disclaimer

Outlines manufacturer warranty conditions and liability limitations for improper use.

Safety Precautions

2.1 Marking of safety precautions

Explains the meaning of symbols like Warning, Caution, and Note for safety communication.

2.3 General safety precautions

Emphasizes adherence to instructions to prevent serious hazards to personnel and systems.

2.3.1 Special symbols

Details various safety symbols and their specific meanings for user guidance.

2.3.2 Information on use of safety equipment

Provides guidelines on wearing appropriate safety equipment for protection.

Installation

5.2 Safety precautions for installation and assembly

Lists critical safety measures to be followed during installation and assembly.

Commissioning

6.1 Preparation for commissioning

Covers pre-commissioning checks, oil addition, and regulatory compliance.

6.2 Checking direction of rotation

Explains the procedure for verifying correct shaft rotation to prevent system damage.

6.3 Test run

Details the steps and safety precautions during the initial test run.

Maintenance

7.1 Safety precautions

Lists essential safety guidelines for all maintenance, assembly, and repair activities.

7.2 Oil level

Stresses the importance of regular oil level checks for operational safety.

7.2.1 Oil level check via oil filler opening

Provides a step-by-step guide for safe oil level inspection.

7.3 Oil change

Details the procedures and warnings associated with performing an oil change.

7.5 Maintenance intervals

Presents reference values for various maintenance tasks based on operating hours.

Lubricants and Operating Materials Maintenance Parts

8.1.1 Oil recommendation

Provides guidance on selecting appropriate oils and brands for the compressor air ends.

8.1.5 Pressure dew point of compressed air

Explains how to determine pressure dew point using atmospheric conditions and pressure.

Technical Data and Tightening Torques

9.1 Technical data

A table presenting key technical specifications for various EVO compressor air end models.

Troubleshooting

ROTORCOMP EVO6 Specifications

General IconGeneral
BrandROTORCOMP
ModelEVO6
CategoryCompressor
LanguageEnglish

Related product manuals