EasyManuals Logo

Ruckus Wireless R750 User Manual

Ruckus Wireless R750
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
R750 Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions on
how to install and begin using your Ruckus R750 Dual-Band
802.11ax Indoor Wi-Fi Access Point (AP). After completing the
steps described in this guide, you will be able to place the R750
at your site and begin providing wireless access to users.
FIGURE 1 R750- Top
This Guide in Other Languages
请从以下网站获得该指南的简体中文版 https://
support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com.
このガイドの日本語版は https://support.ruckuswireless.com
ご覧ください。
가이드의 한국어 버전은 사이트 (https://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
Veja a versão em português (Brasil) deste guia em https://
support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía
en https://support.ruckuswireless.com.
Before You Begin
Before deploying Ruckus products, please check for the latest
software and the release documentation.
Release Notes and other user documentation are available at
http://support.ruckuswireless.com/documents.
Software upgrades are available at http://
support.ruckuswireless.com/software.
Software license and limited warranty information are
available at http://support.ruckuswireless.com/warranty.
Package Contents
A complete R750 installation package includes all of the items
listed below:
R750 Access Point
One wall-mount anchor kit, including two 1" No. 8 steel pan
head Phillips sheet metal screws and wall-mount anchors
One external T-bar bracket (two unassembled parts)
Service Level Agreement/Limited Warranty Statement
Declaration of Conformity
Regulatory Statement
Ruckus Access Point Getting Started Guide
AP Cloud Management Insert
This Quick Setup Guide
Step 1: Collecting Setup Requirements,
Hardware and Tools
Admin PC (computer with an Ethernet port and Wi-Fi adapter)
Cat 5e (or better) Ethernet cable
Ruckus Wireless 48VAC power adapter (sold separately) --OR--
802.3at-compliant Power over Ethernet (PoE) switch or PoE
injector
Optional hardware and tools:
Customer-supplied small padlock with a 3.5mm (0.14") or
smaller shackle diameter, used to lock the AP to prevent
removal.
Customer-ordered Ruckus Wireless 902-0120-0000 secure
mounting bracket kit:
If you are mounting the AP on a at surface using the secure
mounting bracket kit, then you need an electric drill with
4.75mm (3/16”) drill bits.
If you are mounting the AP on a pipe or pole using the
secure mounting bracket kit, then you will also need a
38.1mm to 63.5mm (1.5" to 2.5") pipe or pole, two pole
clamps, and hand tools to tighten the clamps.
Step 2: Connecting Your Computer to the
AP
1. Using an Ethernet cable, connect your computer’s network
port to the 2.5G ETH PoE port on the AP (1 in the Figure
below).
2. Connect the AC cable of the AC power adapter to a
convenient and protected power source. Connect the DC
output cable of the AC power adapter to the AP's 48Vdc port.
NOTE: Alternatively, connect the 2.5G ETH PoE port to a
PoE injector or switch for both power and network
connectivity.
FIGURE 2 AP Ports
TABLE 1 R750 bottom panel elements
No. Label Description
1 2.5G
ETH PoE
100/1000/2500 Mbps PoE In Port:
RJ-45 Ethernet port (supports
802.3af/at PoE in)
2 1G ETH 10/100/1000 Mbps port: RJ-45
Ethernet port (non-PoE)
3 48V
0.75A
48V DC input
4 USB USB Port
Max Dimensions: 6cm x 2cm x
1.1 cm
Interface: USB 2.0
Connector: USB – Type-A plug
3. Verify that the PWR LED on the AP is a steady green.
Step 3: Preparing Your Computer for AP
Setup
NOTE: The following procedures assume Windows as the
operating system. Procedures for other operating systems are
similar.
1. On your Windows PC, congure your network adapter from
the Local Area Connection settings as follows:
Start > > Control Panel > Network and Sharing Center >
Change Adapter Settings
2. Edit the TCP/IPv4 address settings as follows:
Local Area Connection > Properties > Internet Protocol
Version 4 (TCP/IPv4) > Properties
The Internet Protocol Version 4 (TCP/IPv4) Properties dialog
box appears.
IMPORTANT-QSG: Write down all of the currently active
settings so you can restore your computer to its current
conguration later (when this process is complete).
Copyright
©
2019 CommScope, Inc. All rights reserved. Page 1 of 4
Published November 2019, Part Number 800-71927-001 Rev E

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ruckus Wireless R750 and is the answer not in the manual?

Ruckus Wireless R750 Specifications

General IconGeneral
BrandRuckus Wireless
ModelR750
CategoryWireless Access Point
LanguageEnglish

Related product manuals