12
ENGLISH
You can often make adjustments and repairs described
here. For other repairs, have the trimmer serviced by an
authorised service dealer.
INSTALLING PRO CUT II™ LINE TRIMMER HEAD
See Figure 14.
■ Stop the engine and ensure the cut off switch
remains in the off position.
■ Remove current cutting attachment.
■ Install the line head on the drive shaft until fully
seated.
■ Install the spool retainer and turn counter clockwise.
■ Install cutting line as described in the next section of
this manual.
INSTALLING CUTTING LINE IN PRO CUT II™ LINE
TRIMMER HEAD
See Figure 15.
Use monofilament line between 2.4mm and 2.7mm
diameter. Use original manufacturer’s replacement line
for best performance.
■ Stop the engine and ensure the cut off switch
remains in the off position.
■ Gather two of the pre-cut lengths of trimmer line
provided or cut two pieces of trimmer line, in 28cm
lengths.
■ Remove the old line by pulling it from the holes
located on the top of the line head.
■ Insert the line into the slots located on the sides
of the line head. Line should be pushed in until
approximately 2.5cm protrudes from the holes on the
top of the line head.
INSTALLING REEL EASY™ LINE TRIMMER HEAD
■ Stop the engine and ensure the cut off switch
remains in the off position.
■ Remove current cutting attachment.
■ Open the REEL EASY™ line trimmer head by
depressing the latches on each side. The contents of
the line trimmer head are spring loaded, so keep your
other hand over the line trimmer head cover while
depressing the latches.
■ Remove the line trimmer head cover, knob, and spool
and set aside.
■ Place the line trimmer head on the drive shaft. Make
sure the line trimmer head is fully seated.
■ Install the hex bolt into the opening on the drive shaft
and secure using the hex-shaped opening in the
knob to tighten.
Note: Only use the knob to tighten the bolt. The use of
other tools may allow over tightening of the bolt, which
could damage the line trimmer head.
■ If removed, replace the spring into the line trimmer
head and push down to seat.
■ Reinstall the spool. For straight shaft attachments
with the REEL EASY™ cutting head the spool should
be placed so "This side out for straight shaft" is
visible.
■ Replace the knob in the spool.
■ Replace the line trimmer head cover, aligning latches
with openings in the line trimmer head. Press cover
and line trimmer head together until both latches
snap into openings securely.
■ Install line as described in the next section of this
manual.
INSTALLING LINE IN REEL EASY™ LINE TRIMMER
HEAD
Use 2.4mm diameter mono filament line.
■ Stop the engine and ensure the cut off switch
remains in the off position.
■ Cut one piece of line approximately 7.5 meters in
length.
■ Rotate knob on line trimmer head until line on knob
aligns with arrows on top of line trimmer head.
■ Insert one end of the line into eyelet located on
the side of the line trimmer head and push until
line comes out through the eyelet on the other side.
Continue to push line through the line trimmer head
until the middle section of the line is inside the line
trimmer head and line outside the line trimmer head
is evenly divided on each side.
■ Rotate the knob on the line trimmer head to wind the
line. Rotate the knob counterclockwise. Wind the line
until approximately 20cm remains protruding from the
line trimmer head.
CLEANING THE EXHAUST PORT, MUFFLER AND
SPARK ARRESTOR
NOTE: Depending on the type of fuel used, the type
and amount of lubricant used, and/or your operating
conditions, the exhaust port, muffler, and/or spark
arrestor screen may become blocked with carbon
deposits. If you notice a power loss with your petrol
powered tool, you may need to remove these deposits
to restore performance. We highly recommend that only
qualified service technicians perform this service.
The spark arrestor must be cleaned or replaced every
50 hours or yearly to ensure proper performance of your
product. Spark arrestors may be in different locations
depending on the model purchased. Please contact
your nearest service dealer for the location of the spark
arrestor for your model.
IDLE SPEED ADJUSTMENT
See Figure 16.
If the cutting attachment turns at idle, the idle speed
screw needs adjusting on the engine. Turn the idle speed
screw counter clockwise to reduce the idle RPM and
stop the cutting attachment movement. If the cutting
attachment still moves at idle speed, contact a service
dealer for adjustment and discontinue use until the repair
is made.
WARNING:
The cutting attachment should never turn at
RBC430SES/SBS manual(TTIA).indd Sec2:12RBC430SES/SBS manual(TTIA).indd Sec2:12 09-9-23 5:2509-9-23 5:25
To Next Page
