This document is the owner's operating manual for the RYOBI RM-2010 lawnmower, providing comprehensive instructions for assembly, operation, maintenance, and safety.
Function Description
The RYOBI RM-2010 is an electric lawnmower designed for cutting grass. It features a motor-driven blade that rotates to cut grass, with a grass catcher for collection. The cutting height is adjustable to suit different lawn conditions and desired finishes. The lawnmower is intended for domestic use and requires connection to a mains power supply.
Important Technical Specifications
- Model: RM-2010
- Voltage: 230V~50Hz
- Power Input: 2,000W
- No Load Speed: 2,850 min⁻¹
- Cutting Width: 460mm
- Cutting Height: 25/30/40/50/60/70mm (6 adjustable settings)
- Collection Box Capacity: 50L
- Net Weight: 25.0kg
Usage Features
The RM-2010 lawnmower is designed for ease of use and safety.
- Assembly: The manual provides detailed steps for assembling the handlebar and grass catcher. The handlebar assembly involves attaching lower and upper handlebar sections, securing them with bolts and knobs, and positioning cable cleats. The grass catcher is assembled with screws and then attached to the mower deck by raising the rear deflector, aligning hooks, and lowering the deflector.
- Starting and Stopping: To start the mower, the user must first set the desired cutting height, connect to a power supply, then press and hold the safety lock-off button (2) and squeeze the switch lever (1) towards the handle. To stop, the user simply releases the switch lever. A safety note reminds users that the blade continues to rotate for a few seconds after switch-off, and advises against rapid switching on and off.
- Mowing Operation: Users are instructed to start mowing from the edge of the lawn closest to the power point and work away from it, positioning the power cable on the already cut side. A warning emphasizes not to let the motor labor excessively, especially in heavy conditions, and to raise the cutting height if the motor struggles.
- Heavy Growth Management: For areas with heavy growth, the manual recommends mowing without collecting clippings first, then allowing them to dry. If collection is desired, the area should be mown again with the grass collection bag attached, using the maximum cutting height setting. The cutting height can then be progressively lowered until the desired finish is achieved. A crucial tip is not to remove more than one-third of the grass's height in a single cut to prevent damage to the grass.
- Cutting Height Adjustment: The cutting height can be adjusted using a lever. To adjust, the user moves the lever sideways to disengage it from the locking notch, then pulls it backward to lower the cut height or pushes it forward to raise it. The lever must then be released to lock firmly into one of the six notched settings. Users are reminded to stop the mower and wait for the blade to cease rotation before adjusting the height. For the first cut of the season, a high cutting adjustment is recommended.
- Safety Features: The lawnmower incorporates a safety lock-off button to prevent accidental starting. The manual stresses the importance of using an extension cord suitable for outdoor use when operating outdoors. It also advises against operating the mower in wet grass, on excessively steep slopes, or when people or pets are nearby. Users are instructed to always wear eye protection and substantial footwear.
Maintenance Features
Regular maintenance is crucial for the safe and efficient operation of the RYOBI RM-2010.
- Before Each Use: Users should inspect the mower unit for cleanliness and damage. This includes removing grass and debris from around the cutting height adjustment lever, air filter, and underside of the deck. The grass collection bag should be empty and inspected for damage. The rear deflector and mower deck should be checked. Critically, the cutting blade must be inspected for bends, cracks, and secure mounting. All securing nuts and bolts should be tight, and the power supply cable and switch control/safety button should be checked for damage. Any damage found requires repair by a qualified person before use.
- Lubrication: The wheels, pivot points, and linkages should be lubricated after every 25 hours of use.
- General Cleaning: All grass debris should be removed from the top and underside of the mower deck, as well as from ventilation holes, immediately after use. Strong gloves are recommended when working with or around the cutting blade.
- Motor Unit and Switch Control/Safety Button: These components are maintenance-free and should only be accessed by an approved maintenance engineer.
- Blade Replacement: The cutting blade should be replaced after 50 hours of operation or every two years, whichever comes sooner, or immediately if damaged or worn. The replacement process involves turning the mower on its side, firmly gripping the blade with a gloved hand, removing the fixing bolt with a spanner, and carefully removing the old blade. The new blade must be oriented correctly (turned edges facing towards the motor) and located onto the carrier pins before securing it with the fixing bolt.
- Power Supply Cable: The power supply cable should be inspected for signs of damage or aging before each use. Damaged or worn cables should not be used, and all electrical inspections and repairs must be conducted by a qualified electrician.
- Storage: For storage periods exceeding one month, the mower should be thoroughly cleaned, the grass collection box emptied, wheels, pivot points, and linkages lubricated, all metal parts covered with oil to prevent corrosion, and the mower covered with a protective sheet and stored in a dry area.
The manual also includes general safety rules applicable to all power tools, emphasizing work area safety, electrical safety, personal safety, and proper tool use and care. A warranty section outlines the terms and conditions of the 24-month warranty provided by Ryobi.
Need help?
General
To Next Page
