To Next PageTo Next PageWhat to do if Ryobi RY401018 is not bagging properly?
If your Ryobi Lawn Mower isn't bagging properly, it could be due to the cutting height being set too low, or grass blocking the rear chute. To fix this, raise the cutting height. Stop the motor, remove the start key and battery, then remove the grass catcher bag and clear any blockage.
Why does my Ryobi RY401018 motor stop while cutting?
The motor of your Ryobi Lawn Mower might stop while cutting because the cutting height is set too low. Try raising the cutting height to solve this issue.
How to fix Ryobi RY401018 Lawn Mower cutting grass unevenly?
If your Ryobi Lawn Mower is cutting grass unevenly, it may be because the lawn is rough or the cutting height isn't set properly. Adjusting the cutting height should resolve this issue.
Why is my Ryobi RY401018 Lawn Mower not mulching properly?
Your Ryobi Lawn Mower might not be mulching properly if wet grass clippings are sticking to the underside of the deck. Wait until the grass dries before mowing to improve mulching.
Why is my Ryobi RY401018 vibrating at a higher speed?
Your Ryobi Lawn Mower might be vibrating at a higher speed because the blade is unbalanced, excessively or unevenly worn, or the motor shaft is bent. To resolve this, replace the blade. Stop the motor, remove the start key and battery, then inspect for damage. Have it repaired by an authorized service center before restarting.
Why is my Ryobi RY401018 hard to push?
Your Ryobi Lawn Mower might be hard to push due to high grass, the rear of the mower housing and blade dragging in heavy grass, or the cutting height being too low. Raising the cutting height should help.
General| Battery Voltage | 40V |
|---|---|
| Cutting Width | 20 inches |
| Deck Material | Steel |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Side Discharge | Yes |
| Number of Batteries Included | 1 |
| Power Source | Battery |
| Drive System | Rear-wheel drive |
| Battery Amp Hour | 5 Ah |
Understand the product and manual for safe operation.
Protects the battery port from moisture and debris.
Convenient place for storing battery or an extra pack.
Collects grass clippings, prevents discharge across lawn.
Provides cutting height adjustments.
Covers rear discharge opening for finer clippings.
Pulling levers upward engages self-propelled feature.
Directs clippings out when grass is too tall for mulching.
Engage bail, press start button to start motor and blade.
Must be inserted before the mower can be started.
Prevents starting if unit is vertical or tilted > 45°.
Folding handles allow compact, upright storage.
Carefully remove product and accessories, check packing list.
Rotate knobs 90 degrees, raise handle, and re-secure.
Attach grass catcher bag to frame using clips.
Lift rear discharge door and seat catcher hooks on mower housing.
Insert mulching plug into rear discharge opening.
Align and seat side discharge chute onto mulching cover.
Adjust cutting height using the height adjustment lever.
Align battery ribs with grooves and install/remove from mower port.
Start by engaging bail and pressing start button; stop by releasing bail.
Engage self-propelled feature by pulling levers upward.
Adjust mower speed using the cruise control button on the handle.
Advice on mowing conditions, lawn health, and deck cleaning.
Mow across slopes, exercise caution on inclines and terrain.
Stop mower, open cover, remove battery/key, lift and empty catcher.
Clean plastic parts with dry cloths, avoid solvents.
Bearings are pre-lubricated for life; no further lubrication needed.
Remove old blade, install new blade ensuring correct orientation and torque.
Store indoors in a dry location, lower handle assembly, avoid cables.
