To Next PageTo Next Page
Need help?Do you have a question about the Safety 1st Grow and Go and is the answer not in the manual?
General| Rear-Facing Weight Range | 5-40 lbs |
|---|---|
| Forward-Facing Weight Range | 22-65 lbs |
| Booster Mode Weight Range | 40-100 lbs |
| Harness Type | 5-point harness |
| Recline Positions | 3 |
| Machine Washable Cover | Yes |
| Side Impact Protection | Yes |
| Installation Type | LATCH system |
| Height Range | 19 to 52 inches |
| Cup Holder | Yes |
Guide to measuring child's weight and height for proper car seat selection.
Steps to adjust the car seat to fit your child correctly for safety.
Instructions on how to properly install the car seat into your vehicle for secure use.
Guidance on how to snugly secure your child in the car seat for optimal protection.
Identifies key parts like headrest, harness, recline handle, and base.
Details harness slots, chest clip, buckle, splitter plate, and tether strap locations.
Use and removal instructions for comfort harness covers.
Instructions for removing and installing the buckle cover.
Guidance on attaching and removing head and body pillows for infants.
Child 5-40 lb, 19-40 in. Ride rear-facing until limits reached.
Child 22-65 lb, 29-49 in., min 1 year. Ride forward-facing until limits.
Child 40-100 lb, 43-52 in. Use booster until limits reached.
Steps to loosen straps, unbuckle, release chest clip, and prepare harness.
Place child in seat to determine proper harness fit and strap placement.
Child's head must be below headrest top; straps at or below shoulders.
Use 1st or 2nd slot, closest to child, not underneath.
Child's ears below headrest top; straps at or above shoulders.
Measure child's shoulder height to ensure it's within limits.
Steps to loosen straps and adjust headrest height for proper fit.
Steps to unbuckle, recline seat, and locate metal retainer.
Rotate metal retainer and push through slot, then tuck cover.
Pull buckle to ensure it is securely locked in place.
Adjust buckle strap and harness strap length for a snug fit on smaller infants.
Steps to thread harness straps through lower slots and attach to splitter plate.
Seat has 3 positions for rear/forward-facing and booster modes.
Use recline handle to adjust seat angle for proper fit.
Universal system for installing car seats without vehicle belts.
Check vehicle for LATCH anchor bar locations for secure installation.
Both methods are safe; do not use both simultaneously.
Identifies hooks, adjuster, and storage attachment for LATCH belt.
Instructions for detaching and storing the lower anchor belt.
Illustrates lap/shoulder belts used for car seat installation.
Use vehicle belt if LATCH is unavailable or child exceeds weight limit.
Steps to lock car seat using vehicle belt for secure installation.
Consult manual for belt/seating position compatibility.
Verify the vehicle belt locks properly to prevent loosening.
Explains switchable, automatic, and emergency locking retractors.
Test if latch plate locks by tugging belt; check for sliding.
Identify sliding latch plates that require a locking clip.
Lists incompatible belts like Emergency Locking Retractor Lap Only.
Tether improves installation stability and reduces injury risk in crashes.
Connect tether hook to designated vehicle anchor point securely.
Store tether strap securely when not in use for rear-facing or booster modes.
Procedures for tightening and loosening the tether strap for proper tension.
Do not use tether for rear-facing mode; secure hook to storage.
Never place child rear-facing near an active frontal airbag.
Verify child's fit and check harness/buckle for adjustments.
Position the car seat in the back seat for rear-facing installation.
Ensure correct recline angle using level line for child's age.
Confirm vehicle belts work with car seat and have a locking mechanism.
Identify the correct belt path for threading the vehicle belt.
Thread vehicle belt through designated path, ensuring no twists.
Connect the vehicle belt buckle tongues securely.
Push seat down, pull belt taut to remove slack.
Ensure seat movement is limited to 1 inch side-to-side.
Verify child's fit and check harness/buckle for adjustments.
Remove LATCH lower anchor belt from its storage location.
Identify the correct belt path for threading the LATCH belt.
Thread LATCH belt through designated path, ensuring no twists.
Ensure correct recline angle using level line, use padding if needed.
Thread LATCH hook through belt path opening, ensuring no twists.
Position the car seat in the back seat for rear-facing installation.
Ensure correct recline angle using level line, use padding if needed.
Connect LATCH hooks securely to vehicle's lower anchor bars.
Push seat down, pull belt taut to remove slack.
Ensure seat movement is limited to 1 inch side-to-side.
Final check to ensure the car seat is securely installed and has not loosened.
Child 22-65 lb, 29-49 in., min 1 year. Use until limits.
Methods include vehicle belt + tether or LATCH + tether.
Do not use LATCH for children over 40 lbs; use vehicle belt instead.
Verify child's fit and check harness/buckle for adjustments.
Position the car seat in the back seat for forward-facing installation.
Make seat flush against vehicle seat back, ensuring upright seat back.
Loosely attach tether hook to vehicle's tether anchor.
Confirm vehicle belts work with car seat and have a locking mechanism.
Identify the correct belt path for threading the vehicle belt.
Thread vehicle belt through designated path, ensuring no twists.
Push seat down, pull belt taut to remove slack.
Ensure seat movement is limited to 1 inch side-to-side.
Final check to ensure the car seat is securely installed and has not loosened.
Guide on how to properly secure your child in the installed car seat.
Verify child's fit and check harness/buckle for adjustments.
Remove LATCH lower anchor belt from its storage location.
Identify the correct belt path for threading the LATCH belt.
Thread LATCH belt through designated path, ensuring no twists.
Position the car seat in the back seat for forward-facing installation.
Make seat flush against vehicle seat back, ensuring upright seat back.
Loosely attach tether hook to vehicle's tether anchor.
Connect LATCH hooks securely to vehicle's lower anchor bars.
Push seat down, pull belt taut to remove slack.
Ensure seat movement is limited to 1 inch side-to-side.
Ensure child sits flat, harness over shoulders and thighs.
Insert buckle tongues until they click, then pull straps tight.
Slide clip to mid-chest, level with armpits, away from neck.
Pinch test: if fingers slip off, harness is tight enough.
Child 40-100 lb, 43-52 in. Use until limits reached.
Use vehicle belt only. Keep seat belted when not in use.
Never use harness; fit shoulder belt snugly; do not place belt under arms.
Steps to unbuckle and remove the harness buckle.
Adjust headrest, undo fasteners, and store harness components.
Undo fasteners on seat pad and headrest pad.
Gently pull headrest pad off and thread straps through slots.
Place chest clip, straps, and buckle tongues behind headrest.
Child's ears must not be above booster headrest.
Belt across shoulder and chest, not face or neck.
Measure child's shoulder height to ensure it's within limits.
Belt across hips, not stomach.
Ensure seat back is upright, use position 1 or 2 for flush fit.
Check for headrest interference; consult manual.
Guide for the child to sit correctly in the booster seat.
Unbuckle harness, loosen straps, adjust headrest, undo pad fasteners.
Remove elastic straps, headrest pad, seat pad fasteners, and lower headrest.
Route lap belt through path, across hips, not stomach.
Secure the vehicle lap belt.
Shoulder belt under holder, across shoulder and chest.
Periodically check child's position and shoulder belt tightness.
Machine wash pad/accessories cold, gentle cycle. Tumble dry low heat.
Spot clean harness straps with warm sudsy water. Check for wear damage.
Steps to reattach headrest pad, slide harness straps, and secure components.
Steps to insert buckle retainer into the correct slot.
Use 1st/2nd slot for rear-facing; any slot for forward-facing.
Adjust headrest, undo fasteners, and loosen harness straps.
Pull chest clip, straps, and buckle tongues out; slide straps into headrest openings.
Thread buckle/chest clip, then harness straps through shoulder slots and splitter plate.
Certified for aircraft with internal harness; not as booster.
Install in window seat, follow airline policies, use forward-facing seats.
Follow rear-facing and forward-facing steps for aircraft installation.
Replace after minor crash (if criteria not met) or moderate/severe crash.
Do not use car seat more than 10 years from the manufacture date.
Never leave child unattended; use approved accessories; do not modify.
Use only in passenger vehicles; avoid boats, motorcycles, etc.
Check belts/anchors; secure restraint even when empty.
Never place child rear-facing near an active frontal airbag.
Rear seats are safest; avoid side or rear-facing seats.
Park in shade, cover seat, check for hot surfaces before use.
Register product via mail or online for safety recall notifications.
Contact US Govt. Safety Hotline for recall information.
Locate model number, manufacture date, and line code on seat label.
One-year warranty against defects; original receipt required.
Excludes misuse/abuse; limits damages to direct/consequential.
Warranty provides specific legal rights that vary by state.
Clean debris from lever/retractor; do not lubricate.
Straighten straps each time; tighten harness to prevent twisting.
List of parts (buckle, pad, clip, tether) with associated costs.
Contact Consumer Care by phone or text; accepts Visa/MasterCard.
DJG's commitment to comfort, convenience, and child safety.
Proper use lowers injury risk; parents as role models.
Provides phone, text, and website for support and inquiries.
