Samlexpower EVO-RC-PLUS - Page 33

SAMLEX AMERICA INC. | 33
SECTION 4 | Parameter Setup
4.1.3.3 "Select Parameter" Menu Map for Parameter Group 5: OTHER FUNCTION
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* P O W E R S A V I N G
0 = D i s a b l e
Screen
No. 1
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* E N T E R P O I N T
6 W
Screen
No. 2
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* W A K E U P P O I N T
7 W
Screen
No. 3
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* R E L A Y F U N C T I O N
2 = G e n e r a t o r 0
Screen
No. 5
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* C O M M . I D
1
Screen
No. 6
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* D E F A U L T R E S E T
0 = N o
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* D I A L O G T I M E
1 = 1 s e
c
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* P A R A M E T E R S A V E
0 = N o
Screen
No. 9
Screen
No. 10
Screen
No. 11
ð ð ð ð
ð ð ð ð
ð
ð
ð ð
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* R E M O T E S W I T C H
0 = B u t t o n
Screen
No. 4
ð
ð
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* B U Z Z E R
1 = O n
Screen
No. 7
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* D I S C H A R G E B E E P
1 = O f f
Screen
No. 8
ð ð
ð ð
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* T E M P U N I T
0 = C
S e l e c t P a r a m e t e r
O T H E R F U N C T I O N
* P A S S W O R D D I S A B L E
0 = D i s a b l e
Screen
No. 12
Screen
No. 13
ð
ð
ð ð
See NOTE 3
ð
ð
ð
ð
NOTES:
1. Value shown in the 4
th
line of the display screen is the default
/ factory pre-set values (EVO-1212F / 1212F-HW in this
case). For the default / factory pre-set values and additional
programming details for the other Models, refer to Table 4.8
(Section 4.8) for “OTHER FUNCTION”
2. Asterisk sign * in the beginning of the 3
rd
line of the display
screen points that the parameter shown in this line will be se-
lected for further programming when the Enter Key is pressed
3. Screen No. 5 is displayed only in Model Nos. that have Generator
input terminals. These screens are NOT displayed in EVO-1212F /
1212F-HW and EVO-1224F / 1224F-HW
4. Use ñ and ò Keys to navigate to the desired screen.
Up Key
Down Key
ð
ð
Fig 4.4 "Select Parameter" Menu Map for Parameter Group 5: OTHER FUNCTION