Samlexpower EVO-RC-PLUS

Questions and Answers

M
michaelbeckAug 21, 2025
How to resolve transformer overheat on Samlexpower Remote Control?
- A
  April AndersonAug 21, 2025
  To resolve a transformer overheat issue with your Samlexpower Remote Control, first, verify that the fans are functioning correctly and that there are no obstructions blocking the air suction and discharge vents. Ensure that there is adequate cool air available and that the ambient temperature is within acceptable limits. If the problem persists, reduce the load or the 'BULK CURRENT'.
L
lskinnerAug 23, 2025
What causes heat sink to overheat on Samlexpower Remote Control and how to fix it?
- J
  Jamie RojasAug 23, 2025
  If the heat sink on your Samlexpower Remote Control is overheating, check that the fans are working correctly, and there are no blockages of air suction and discharge vents. Make sure adequate cool replacement air is available, and the ambient temperature is within the specified limits. If the issue continues, reduce the load and the 'BULK CURRENT'.
K
Kimberly McleanAug 26, 2025
What to do if Samlexpower Remote Control shows 'Input over current'?
- A
  Anthony McdonaldAug 26, 2025
  If your Samlexpower EVO™ Inverter/Charger displays an 'Input over current!' message, it will require a manual reset. Power off the unit, wait for one minute, and then power it back on. Also, ensure that the set threshold of 'GRID MAX CURRENT' or 'GEN MAX CURRENT' matches the breaker capacity of the AC input source or AC input Branch Circuit. If the AC input current capacity cannot be increased, reduce the AC load or 'BULK CURRENT' accordingly.
K
Kimberly CastanedaAug 27, 2025
Why Samlexpower Remote Control shows 'Output over current' and how to fix it?
- R
  Richard BarnesAug 28, 2025
  If your Samlexpower EVO™ Inverter/Charger is showing an 'Output over current!' error, it will require a manual reset. You should power OFF the unit, wait for 1 minute, and then power it ON again. Make sure that the maximum instantaneous surge current of the load does not exceed 300% of the rated current of the EVO™ Inverter/Charger for 1 millisecond.
L
Laura HutchinsonSep 1, 2025
What to do for 'Output over load' on Samlexpower Remote Control?
- W
  wzimmermanSep 1, 2025
  If your Samlexpower EVO™ Inverter/Charger displays 'Output over load!', it requires a manual reset. Power it OFF, wait one minute, then power it ON again. Ensure overloading is limited to the specified limit: Output voltage should be less than 96Vrms for 300 cycles (5 seconds at 60Hz).
W
wrodriguezSep 3, 2025
How to fix 'Battery over voltage' on Samlexpower Remote Control?
- T
  Tammy WilliamsSep 3, 2025
  The 'Battery over voltage!' fault on your Samlexpower Remote Control will clear automatically when the battery voltage drops to 0.5V below the set upper threshold of 'BATT OVER VOLT' in both Inverting and Charging Mode.
T
timothy78Sep 5, 2025
What to do if Samlexpower Remote Control indicates 'Output short circuit'?
- C
  Corey GarciaSep 5, 2025
  If your Samlexpower EVO™ Inverter/Charger displays an 'Output short circuit!' message, it requires a manual reset. Power OFF the unit, wait for one minute, and then power it ON again.
P
Patricia MillerSep 7, 2025
Why is my SD card unusable with Samlexpower Remote Control?
- A
  alexandra85Sep 7, 2025
  If your SD card is unusable with the Samlexpower Remote Control, verify that the format is FAT16/FAT32. Also, check that the card's capacity is less than 16 GB. If necessary, re-format the card.
M
michellehernandezSep 9, 2025
What to do when Samlexpower Remote Control says 'SD card full'?
- M
  Mr. Adam StewartSep 9, 2025
  If your Samlexpower Remote Control indicates that the 'SD card is full!', you should move or delete files from the card, or re-format the card.
M
Mrs. Sara Murray MDSep 12, 2025
How to fix 'SD card read error' on Samlexpower Remote Control?
- P
  patricia58Sep 12, 2025
  To fix an 'SD card read error!' on your Samlexpower Remote Control, remove and re-insert the card.