Samlexpower EVO-RC-PLUS - 4.9 TIME SETTING PARAMETERS; 4.10 STOP SD CARD PARAMETERS

SAMLEX AMERICA INC. | 95
SECTION 4 | Parameter Setup
If SD Card is not
removed within 30 sec,
the unit will reset.
4.9 GROUP 6 PARAMETER SETUP: TIME SETTING
Please refer to Parameter "TIME SETTING" under Screen No. 6 for Group 6 at Fig 4.1. Set up details are given below.
The Date and Time Format is Year/Month/Day Hour:Minute (24 hour clock):
NOTE: Password is not required for setting this parameter.
4.9.1 Programming Steps for Parameter "TIME SETTING"
ð
E V O - 1 2 1 2 F I n v e r t i n g
A C o u t p u t : 1 2 0 . 0 V
< 0 . 1 0 A
6 0 . 0 0 H z
Enter Key
Any Operating Mode Screen from
Fig 3.1 to 3.5
[Above screen is Screen 1 of Fig 3.2(a)]
S e l e c t G r o u p
* C H A R G E C U R V E
ð
S e l e c t G r o u p
* T I M E S E T T I N G
ð
S e l e c t P a r a m e t e r
T I M E S E T T I N G
E n t e r t h e t i m e
2 0
0 0 / 0 1 / 0 1 0 : 0 0
Down Key x 5 times
Enter Key
i
INFO
• Time can be programmed from Year 2000 to 2099 only.
• Month can be programmed from 01 to 12 only.
• Day can be programmed from 01 to 31 only.
• Hour can be programmed from 00 to 24 only.
• Minute can be programmed from 00 to 60 only.
• If the numbers Entered for Month, Day, Hour and Minute are not within the above ranges,
message "OUT OF RANGE!" will be displayed and the display screen will go back to the
previously set time. Setting procedure will have to be re-started.
4.10 GROUP 7 PARAMETER SETUP: STOP SD CARD
Please refer to Parameter "STOP SD CARD" under Group 7 at Fig 4.2. Please note that this set up is displayed / accessible
only when SD Card is inserted in the SD Card Slot (9, Fig 1.1a). Set up details are given below:
Once SD Card is being used, it should be removed/ejected only after the operation of the Card has been stopped as
shown below and message "Please remove SD Card" appears. If the SD card is not removed within 30 sec, it will reset.
After the card is removed, it reverts to the original operating screen.
4.10.1 Programming Steps for Parameter "STOP SD CARD"
ð ð
E V O - 1 2 1 2 F I n v e r t i n g
A C o u t p u t : 1 2 0 . 0 V
< 0 . 1 0 A
6 0 . 0 0 H z
Enter Key Down Key x 1 time
Any Operating Mode Screen from
Fig 3.1 to 3.5
[Above screen is Screen 1 of Fig 3.2(a)]
Password 8052
See Section 4.3.1
See Table 4.9, Screen No. 1
for programmable options
S e l e c t G r o u p
* C H A R G E C U R V E
ð
S e l e c t G r o u p
* S T O P S D C A R D
ð
S e l e c t P a r a m e t e r
S T O P S D C A R D
0 = N o
Down Key x 6 times
Enter Key
P l e a s e r e m o v e
S D C a r d
*
S e l e c t P a r a m e t e r
S T O P S D C A R D
1 = Y e s
ð
Enter Key