What does E1 error mean on a Samsung CM1319A/XEU?
If your Samsung Microwave Oven displays 'E1', it could be due to an improper input power frequency or a defective Ass’y Main P.C.B. Check if the power frequency is 50Hz. Replace the Ass’y Main P.C.B or MICOM.
What to do if Samsung CM1319A/XEU Microwave Oven timer counts down but no heat?
If your Samsung Microwave Oven's timer starts counting down but there's no microwave oscillation (no heat, but the oven lamp and fan motor turn on), it could be due to an open or loose connection in the high voltage circuit, especially the magnetron filament circuit, or defective high voltage components like the H.V. Transformer, H.V. Capacitor, H.V. Diode, H.V. Fuse, or Magnetron. Adjust the door and latch switches. Check the high voltage components according to the component test procedure and replace them if defective.
Why Samsung CM1319A/XEU does not accept key input?
If your Samsung Microwave Oven does not accept key inputs for programming (CM1929/1629/1329 models), it could be because the key input is not in sequence, there's an open or loose connection of the membrane keypad to the Ass’y PCB, the membrane panel is shorted or open, or the Ass’y PCB is defective. Refer to the operation procedure and replace the PCB main.
Why Samsung Microwave Oven stirrer does not rotate?
If the drive motor in your Samsung Microwave Oven isn't working (the Ass’y stirrer doesn't rotate), it could be due to an open or loose wiring of the turntable motor, a defective turntable motor, or a defective ass’y stirrer. Check the wire of the drive motor. Replace the drive motor or the ass’y stirrer.
What to do if my Samsung CM1319A/XEU shows Gas Sensor Error E-11?
If your Samsung Microwave Oven displays a Gas Sensor Error E-11, the suggested solution is to check the sensor part and the connection of the sensor housing and the PCB’s connector.
What does E42 error mean on a Samsung CM1319A/XEU Microwave Oven?
If your Samsung Microwave Oven displays error code E42, it could be due to a Power Relay (RY5) failure, loose lead wires of Power Relay (RY5), a Primary or Monitor S/W failure, loose lead wires of Primary or Monitor S/W, a blown fuse (10A) on the neutral area of the Assy Noise Filter, or a H.V.Trans input power sensing circuit failure. Check the Power Relay2, Primary S/W, Monitor S/W or Fuse and replace if defective. Also, check if lead wires are loosened and repair as necessary. Check the circuitry.
Why is my Samsung CM1319A/XEU Microwave Oven sparking?
If your Samsung Microwave Oven is sparking, it is likely due to metallic ware or cooking dishes touching the oven wall, or ceramic ware trimmed with gold or silver powder. Ensure you are using proper cookware and avoid any items with metallic trimming.
What to do if my Samsung CM1319A/XEU doesn't operate and returns to plugged in mode?
If your Samsung Microwave Oven does not operate and returns to the plugged-in mode, it is likely due to a defective Ass’y PCB. Replace the PCB main.
What to do if my Samsung Microwave Oven displays Temp. Sensor Error: E-25?
If your Samsung Microwave Oven displays a Temp. Sensor Error E-25, cool down the set and restart it.
What to do if my Samsung CM1319A/XEU displays Temp. Sensor Error: E-21?
If your Samsung Microwave Oven displays a Temp. Sensor Error E-21, check the sensor part and the connection of the sensor housing and PCB’s connector.
General| Brand | Samsung |
|---|---|
| Model | CM1319A/XEU |
| Category | Microwave Oven |
| Language | English |
To Next Page
