Samsung DV431AEP/XAA User Manual (English)

Other manuals for Samsung DV431AEP/XAA

User Manual120 pages

Service Manual49 pages

Questions and Answers:

L
Leah LandryAug 17, 2025
Why is my Samsung DV431AEP/XAA Dryer not drying properly?
- J
  Jessica SantiagoAug 17, 2025
  There are several reasons why your Samsung dryer might not be drying clothes properly. It could be due to a lint filter that is not clean, a restriction in the exhaust, or an outside exhaust hood damper door stuck closed. The exhaust might be too long, have too many elbows, or flex ductwork might be installed. Poor intake air, incorrect tumbler speed, a slipping tumbler belt, or a bound blower impeller could also be the cause. Overloading the dryer or selecting the wrong cycle for the fabric content can also lead to improper drying. In addition, clothes too wet from the washer can contribute to this issue.
H
hessmichelleAug 20, 2025
Why won't my Samsung Dryer start?
- P
  phillipsdanielleAug 20, 2025
  If your Samsung dryer won't start, ensure all wires are hooked up to their corresponding terminals and that the dryer is plugged in. Check for a blown fuse or circuit breaker. Make sure the door switch is functional and the door is closed, and check for error code 3. Confirm the Start/Pause rotary selector dial is functional and the control board is operational. Also, verify if the belt is off or broken, which activates the Belt Cut-off Switch, and ensure the drive motor is functional. Check the motor winding resistance: it should be 2.88ohms between pin #3 and 4, and 3.5ohms between pin #4 and 5.
J
justin81Aug 23, 2025
How to troubleshoot a noisy Samsung DV431AEP/XAA Dryer?
- K
  kayla67Aug 23, 2025
  To troubleshoot a noisy Samsung dryer: - For thumping, check for a loose tumbler baffle, worn or misaligned rear tumbler rollers, an out-of-round tumbler, or a high weld seam on the tumbler. - For ticking, check for a loose wire harness or an object caught in the blower wheel area. - For scraping, check for a front or rear bulkhead felt seal out of position or worn tumbler front bearings. - For roaring, check for a blower wheel rubbing on the blower housing or bad motor bearings. - For popping or squealing, check for a sticky or frayed belt.
L
Laura BensonAug 26, 2025
Why won't my Samsung DV431AEP/XAA heat, even though the motor runs?
- D
  David JordanAug 26, 2025
  If your Samsung dryer's motor runs but it won't heat, it could be due to an open heating element, a hi-limit that trips easily or is open, or a regulating thermostat that trips easily or is open. A membrane switch might also be open. It is also recommended to check the thermistor.
P
phillipsrebeccaAug 28, 2025
What to do if my Samsung DV431AEP/XAA Dryer motor runs but the tumbler won't turn?
- A
  Ashley HuffAug 28, 2025
  If the motor in your Samsung dryer runs but the tumbler does not turn, it could be due to a belt that is off, broken, or damaged. Another possible cause is an idler tension spring that is too weak or stretched. Also, check if the idler pulley is jammed or stuck.
D
douglaspriceAug 31, 2025
Why does my Samsung Dryer run for a few minutes and then stop?
- P
  Patrick ThomasAug 31, 2025
  Your Samsung dryer might stop after running for a few minutes due to lint buildup around the drive motor, low voltage, a blower impeller blocked in the blower housing, or the drive motor's start switch contacts being stuck closed.
A
Aaron BrownSep 2, 2025
What to do if my Samsung DV431AEP/XAA Dryer blows fuses or trips the circuit breaker?
- L
  Larry WilliamsSep 3, 2025
  If your Samsung dryer is blowing fuses or tripping the circuit breaker, check if the belt is well connected, if the winding of the motor is continuous (rotor winding, stator winding, generator), and if the motor protector is normal. If these points are normal, the PCB assembly might be out of order and need replacement.
D
Denise ValenciaSep 5, 2025
What causes a Samsung gas dryer to blow fuses or trip the circuit breaker?
- J
  James OsborneSep 5, 2025
  If your Samsung gas dryer blows fuses or trips the circuit breaker, it could be due to the dryer drawing amperages above the normal range during ignition or with the burner on, indicating a fault in the house wiring, fuse box, or circuit breaker. Other potential causes include a loose igniter harness shorted to the base, incorrect wiring or a wire shorted to ground, or a drive motor winding shorting to ground.
C
curryjoseSep 8, 2025
What causes the igniter in my Samsung DV431AEP/XAA Dryer not to glow?
- D
  Dawn HolderSep 8, 2025
  If the igniter in your Samsung dryer does not glow, potential causes include an open flame sensor, an open igniter, or a shorted booster coil. It could also be due to open wiring, a bad motor switch (neutral supply), or no power from the control (L1 supply).
M
Michael EllisSep 12, 2025
Why does my Samsung DV431AEP/XAA Dryer's igniter glow, but there's no gas ignition?
- A
  Alison WileySep 12, 2025
  If the igniter in your Samsung dryer glows, but there's no gas ignition, it could be due to an open secondary coil, an open holding coil, or an open wire harness. A stuck flame sensor (stuck closed) could also be the cause.

Samsung DV431AEP/XAA Specifications

General

Brand	Samsung
Model	DV431AEP/XAA
Type	Electric Dryer
Color	White
Vent Type	Vented
Number of Drying Cycles	12
Energy Star Certified	No
Wrinkle Care Option	Yes
Moisture Sensor	Yes
Control Type	Electronic Touch