Need help?Do you have a question about the Samsung joule HHSM-G600005-1 and is the answer not in the manual?
Defines DANGER, WARNING, CAUTION, NOTICE. Provides specific safety instructions.
Guidance on selecting the optimal location for the outdoor unit.
Instructions for supporting the outdoor unit on ground or wall.
Recommendations for installing the unit in areas with low ambient temperatures.
General guidelines and specific advice for installing the unit.
Guidance on setting expansion vessel capacity and pre-charge pressure.
Estimating pipework water volumes based on pipe size and length.
Ensuring the system is protected from over-pressurisation.
Importance of filter/strainer installation and cleaning.
Requirements for pipe or duct insulation to reduce heat loss.
Guidance on mounting and connecting the flow sensor.
Specifications for power cables used with the outdoor unit.
Requirements for communication cables.
Diagram illustrating power cable connections.
Diagram illustrating communication cable connections.
Table showing compatibility between outdoor units and cylinders.
Schematic diagrams of the SmartPlumb cylinder.
Guidelines for safely transporting and handling the SmartPlumb unit.
Recommendations for choosing an appropriate installation location.
Instructions for installing the SmartPlumb cylinder unit.
Guidance on ensuring adequate space for ventilation and maintenance.
Overview of the SmartPlumb electrical system connections.
Power requirements for the SmartPlumb Pre-Plumb tank.
Ensuring the integrity of the protective earth system.
Connecting the communication cable between units.
Connecting the flow sensor to the MIM casing.
Connecting external controls to the SmartPlumb unit.
Schematics showing examples of external control connections.
Requirements for connecting pipes to the cylinder.
Connecting the primary heat pump circuits.
Connecting heating zone pipes and valves.
Fitting the inlet control set, including expansion relief valve.
Guidance on selecting and mounting the potable expansion vessel.
Recommendations for hot water distribution pipework.
Details on secondary pumped circulation systems.
Steps for commissioning the potable water system.
Information on the heating system fill, flush, and flow meter.
Overview of components for different cylinder sizes.
Guidelines for safely transporting and handling the unit.
Recommendations for choosing an appropriate installation location.
Instructions for installing the Kodiak cylinder unit.
Guidance on ensuring adequate space for ventilation and maintenance.
Overview of the Kodiak electrical system connections.
Power requirements for the Kodiak Compact unit.
Ensuring the integrity of the protective earth system.
Connecting the communication cable between units.
Connecting external controls to the Kodiak unit.
Schematics showing examples of external control connections.
Visual examples of correct discharge pipe arrangements.
Diagram illustrating the waterway connections.
Requirements for connecting pipes to the cylinder.
Connecting the primary heat pump circuits.
Description of the automatic integral bypass function.
Connecting heating zone pipes and valves.
Fitting the inlet control set, including expansion relief valve.
Guidance on selecting and mounting the potable expansion vessel.
Recommendations for hot water distribution pipework.
Details on secondary pumped circulation systems.
Steps for commissioning the potable water system.
Procedure for filling the heating system.
Steps for filling before the heat pump is powered on.
Steps for filling after the heat pump is powered on.
Recommended flow rates for efficient heat pump operation.
Procedure for accessing and using the self-test mode.
Procedure for accessing the zone valve motor head.
Steps to access and remove motor heads from the brass manifold.
Procedure for removing the cover to access components.
Steps for safely removing and replacing the flow sensor.
List and description of all parts used in the system.
General notes on servicing and spare parts.
Steps for safely draining the unit.
Essential checks to be performed during annual servicing.
Schematic diagrams of the Kodiak Compact unit.
Guidelines for safely transporting and handling the unit.
Recommendations for choosing an appropriate installation location.
Instructions for installing the Kodiak Compact unit.
Guidance on ensuring adequate space for ventilation and maintenance.
Overview of the Kodiak Compact electrical system connections.
Power requirements for the Kodiak Compact unit.
Ensuring the integrity of the protective earth system.
Connecting the communication cable between units.
Connecting external controls to the Kodiak Compact unit.
Schematics showing examples of external control connections.
Visual examples of correct discharge pipe arrangements.
Diagram illustrating the waterway connections.
Connecting the primary heat pump circuits.
Connecting heating zone pipes and valves.
Fitting the inlet control set, including expansion relief valve.
Guidance on selecting and mounting the potable expansion vessel.
Recommendations for hot water distribution pipework.
Details on secondary pumped circulation systems.
Steps for commissioning the potable water system.
General notes on servicing and spare parts.
Steps for safely draining the unit.
Essential checks to be performed during annual servicing.
Overview and initial start-up procedure for the controller.
Instructions for setting the controller's time and date.
How to add, edit, or delete schedules.
Procedure for accessing the controller's service menu.
Accessing and using the self-test mode for component testing.
How to view and adjust field setting values.
Instructions for enabling the energy monitoring function.
Adjusting parameters for heating and DHW settings.
Procedure for turning on heating and domestic hot water functions.
Steps to enable heating operation for zones.
How to manually activate or deactivate quiet mode.
How to schedule quiet mode automatically.
Instructions on how to check water flow rate via the controller.
Mechanical diagram of the Smart Plumb Pre-plumbed system.
Electrical diagram of the Smart Plumb Pre-plumbed system.
Mechanical diagram for Kodiak Compact installation.
Electrical diagram for Kodiak Compact installation.
Mechanical diagram for unplumbed installation.
Electrical diagram for unplumbed installation.
Field settings for Smart Plumb and Kodiak Compact units with 2 or 3 zones.
Field settings for unplumbed cylinder units.
Information regarding commissioning procedures.
Requirements for annual servicing to validate the product warranty.
Checks to be performed on the outdoor unit for warranty validation.
Checks to be performed on the indoor unit for warranty validation.
Checks related to the system for warranty validation.
Checks related to operation for warranty validation.
Details on standard and extended warranty periods.
Steps and conditions for redeeming the extended warranty.
Terms and conditions specific to Samsung products.
Scope and limitations of the warranty coverage.
Procedure for making a warranty claim.
Policies on product transfer and warranty exclusions.
Governing law and jurisdiction for promotional terms.
Specific exclusions for Joule Cyclone warranty.
Warranty details for unvented kits and other components.
To Next Page
General