To Next PageTo Next PageWhat to do if Memory(EEPROM) Read Write error occurs on wired remote controller of Samsung Heating System?
If you encounter a Memory(EEPROM) Read Write error (Wired remote controller data error) on your Samsung Heating System, check the wired remote controller.
What to do if a gas leak error is detected in Samsung Heating System?
If your Samsung Heating System indicates a gas leak error, you should check the coolant charging status. Also, examine the indoor EVA sensor. Ensure the outdoor unit service valve is open and verify that the indoor/outdoor installation pipe and wiring are correctly installed.
How to fix [Inverter] total current error/ PFC over current error in Samsung Heating System?
If your Samsung Heating System is showing an inverter total current error or PFC over current error, begin by checking the input power. Next, verify the coolant charging status. Finally, ensure that the outdoor fan is operating normally.
How to troubleshoot outdoor fan 1 error on Samsung Heating System?
If your Samsung Heating System is showing an outdoor fan 1 error, you should check the input power connection status. Verify the connection status between the motor and outdoor unit PCB. Also, inspect the indoor/outdoor fuse.
What does Zone 1 water-out temperature sensor error mean on Samsung Heating System?
If your Samsung Heating System displays a Zone 1 water-out temperature sensor error, it indicates a short- or open-circuit error of the Zone 1 water-out temperature sensor.
How to troubleshoot thermostat wrong connection error on Samsung Heating System?
If your Samsung Heating System shows a thermostat wrong connection error, check the wiring of the Hydro Unit Thermostat and verify the cooling/heating signal for concurrent wiring issues.
What to do if IPM is overheated in Samsung Heating System?
If the IPM is overheated in your Samsung Heating System, check the INVERTER PBA's temperature. Power off and cool down the INVERTER PBA, then restart the outdoor unit.
How to troubleshoot indoor temperature sensor (open/short error) -Zone1 on Samsung Heating System?
If your Samsung Heating System displays an indoor temperature sensor (open/short error) for Zone1, check the indoor unit room temperature sensor and the indoor unit PCB connector CNS043(White).
What to do when Samsung Heating System OUTDOOR UNIT is under protection due to overload?
If the outdoor unit of your Samsung Heating System is under protection due to overload, check the cycle status. Also, check the compressor when it starts.
What to do for indoor unit address setting error in Samsung Heating System?
If you encounter an indoor unit address setting error on your Samsung Heating System, check the address setting of the indoor units.
Safety measures for servicing the equipment.
Safety measures against static electricity and PL.
General safety guidelines to prevent hazards.
Safety guidelines for handling refrigerants.
Safety measures during brazing operations.
Safety measures for charging refrigerants.
Key features and technologies of the EHS system.
Specific features of the EHS Split system.
Technical specifications for split outdoor units.
Technical specifications for mono outdoor units.
List of accessories available for the unit.
Step-by-step guide for disassembling the hydro unit.
Step-by-step guide for disassembling the outdoor unit.
Troubleshoot errors related to the wired remote controller.
Resolve operational issues based on observed symptoms.
Diagnose and fix errors specific to the hydro unit.
Essential checks before starting troubleshooting procedures.
Detailed troubleshooting for various system symptoms.
PCB layout for the Tank Integrated Hydro Unit.
PCB layout for the Outdoor Unit.
Wiring diagrams for Hydro Units (3 Phase and 1 Phase).
Wiring diagrams for Outdoor Units (3 Phase and 1 Phase).
Guide to understanding Samsung EHS model naming conventions.
Component list and diagram for split tank hydro units.
Component list and diagram for mono tank hydro units.
Component list and diagram for split hydro units.
Procedure for checking and updating FSV data using S-NET Pro2.
Instructions for exporting and importing EHS FSV values.
Safety measures for servicing the equipment.
Safety measures against static electricity and PL.
General safety guidelines to prevent hazards.
Safety guidelines for handling refrigerants.
Safety measures during brazing operations.
Safety measures for charging refrigerants.
Key features and technologies of the EHS system.
Specific features of the EHS Split system.
Technical specifications for split outdoor units.
Technical specifications for mono outdoor units.
List of accessories available for the unit.
Step-by-step guide for disassembling the hydro unit.
Step-by-step guide for disassembling the outdoor unit.
Troubleshoot errors related to the wired remote controller.
Resolve operational issues based on observed symptoms.
Diagnose and fix errors specific to the hydro unit.
Essential checks before starting troubleshooting procedures.
Detailed troubleshooting for various system symptoms.
PCB layout for the Tank Integrated Hydro Unit.
PCB layout for the Outdoor Unit.
Wiring diagrams for Hydro Units (3 Phase and 1 Phase).
Wiring diagrams for Outdoor Units (3 Phase and 1 Phase).
Guide to understanding Samsung EHS model naming conventions.
Component list and diagram for split tank hydro units.
Component list and diagram for mono tank hydro units.
Component list and diagram for split hydro units.
Procedure for checking and updating FSV data using S-NET Pro2.
Instructions for exporting and importing EHS FSV values.
General