English - 1
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefi eld Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
To register this product, visit : www.samsung.com/register.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
Step 3
:
Connect External Devices
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
Step 1 :
Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1. Lift the cover on the back of the remote upward
as shown in the fi gure to the right.
2. Install two AAA batteries.
✎
Make sure to match the + and - ends of
the batteries to the diagram in the battery
compartment.
3. Replace the cover.
Getting Started
For the very best picture quality, select HD signal sources and use HDMI cables and connections. Note
that many digital cable programs are not in HD. Check with your video provider to ensure your devices are
receiving HD signals.
Step 4 :
Run Plug & Play
When you turn on your TV for the fi rst time, it automatically launches
the Plug & Play function. With Plug & Play, you can select the On
Screen Display language, set the clock mode, and launch the TV’s
channel memorizing process. It also displays connection instructions
similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or
Right arrow buttons on your remote. To make a selection, press the
ENTERE button. To skip a screen, press the MENU button.
To turn on your TV, press the POWER button on the remote or press
the POWER button on the TV. To run Plug & Play, follow these steps:
1
Select Language of the OSD.
Language : English
Plug & Play
U
Move
E
Enter
English
Español
Français
On the Language screen, select the language for the On Screen
Display (OSD) using your remote control, and then press
ENTERE button. The Home Use screen appears.
2
Select ‘Home Use’ when installing this TV in your home.
Plug & Play
L
Move
E
Enter
Store Demo Home Use
Select Home Use, and then press ENTERE button. If you select
Store Demo, the TV will reset your picture and audio settings every
30 minutes. After you press ENTERE button , the Antenna Source
screen appears.
3
Select the Antenna source to memorise.
Air
Cable
Auto
Plug & Play
U
Move
E
Enter m Skip
Start
Start
Start
If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your
TV is attached to an antenna and cable with no box, select Auto.
When done, press ENTERE button on your remote. The Select
Cable System screen appears.
IMPORTANT: If your TV is attached to a cable or satellite box,
skip Steps 3 through 5. After Plug & Play is complete, set your TV to
Channel 3 or 4, according to the directions for your cable or satellite box.
4
Selects the cable system.
Analog
Digital
Plug & Play
U
Move
E
Enter m Skip
STD HRC IRC
STD HRC
Start
IRC
If your TV is attached to a cable system and you have no cable box,
you must select your cable system type. If you have Digital cable, you
must select the cable system type for both Analog and Digital.
After you have selected the cable system type, select Start, and then
press the ENTERE button on your remote.
✎
Most cable systems are Standard (STD) systems. If you are not
sure about what kind of cable system you have, contact your
cable company.
5
Auto Program in Progress.
DTV Cable : -- Cable : -- Cable 28
Plug & Play
E
Enter m Skip
Stop
15%
The TV memorizes the available channels. This process can take
up to 45 minutes.
6
Set the Clock Mode.
Clock Mode : English
Plug & Play
U
Move
E
Enter m Skip
Auto
Manual
After the TV has memorized the channels, choose the Clock
Mode. Select Auto if you have a digital channel in your area. Select
Manual if you don’t, or if you have a cable or satellite box. When
done, press ENTERE button.
✎
If you select Manual, the clock setting screen appears.
7
Set to daylight saving time.
DST : English
Plug & Play
U
Move
E
Enter m Skip
Off
On
Auto
Select the daylight savings time setting: Off, On, or Auto, and then
press ENTERE button.
8
After the time zone screen,
The connection method
for best HD screen quality
is displayed. Press Right
arrow button on your
remote to view each screen
in succession. Press the
MENU button to skip this
section.
9
The Enjoy your TV screen
appears. Then press
ENTERE button.
Step 2
:
Connect Power and Antenna or Cable
Make sure the AC power cord is
plugged in securely to the wall
outlet and the TV.
Use a 75 ohm (round) cable.
or
• Wall cable jack or
• VHF/UHF
Antenna or
• Cable or Satellite
box Ant or Cable
Out
Connect ANT IN to:
Power Input
To Next Page
